Skip to main content

Cutting the Stair Stringer — Cut the Stair Stringer

Beginner4 hours

Part of project

How to Lay Out a Stair Stringer with a Framing Square · Step 6 of 6

Helpful?

In this video

Using a circular saw, carefully cut along all the marked riser and tread lines. It is important to stop the circular saw cut just before it reaches the intersecting line to avoid overcutting and weakening the stringer. The circular saw's round blade cannot make perfectly square internal corners. After all main cuts are made, use a reciprocating saw to finish the internal corner cuts precisely to the intersecting lines. This creates clean, square notches for the treads and risers.

9.2K views623
stairbuilding

75K subscribers

View Channel

FAQs

What is the most critical tool for ensuring accurate stair stringer layout?

The framing square, especially when used with stair gauges, is indispensable for consistently marking the rise and run on the stringer. A construction calculator is also highly recommended to minimize mathematical errors and ensure precise measurements.

How important is accuracy when marking a stair stringer, and what are the safety implications?

Accuracy is paramount for safety; even small errors can lead to uneven steps, creating a significant tripping hazard. Double-check all measurements and markings before cutting, as consistent riser heights and tread depths are crucial to prevent falls.

Can I use different materials for stair stringers, or is pressure-treated pine always necessary?

While pressure-treated pine is excellent for outdoor use or areas prone to moisture, untreated lumber like Douglas fir or Southern Yellow Pine can be used for indoor stairs. Always select straight, knot-free lumber of appropriate dimensions that meets local building codes for structural integrity.

What's a common mistake beginners make when laying out stringers, and how can I avoid it?

A frequent error is forgetting to account for the thickness of the treads and the necessary bottom cut for the finished floor. Ensure you deduct the tread thickness from the bottom riser and factor in the nosing overhang for consistent steps from top to bottom.

Transcript
Hide

my line there every time okay so that was a cut this is my next cut right here now it's going be easier for me to cut from this end okay so this is the very top now I just want to keep making Cuts now the reason I had more than one type of saw or told you to use more than one type of Saw is when I'm going to do most of the cutting with the circular saw but as I cut in here with the circular saw I want to stop before I cross this other line here same thing you're going to watch me I'm going to turn I'm going to come from here and I'm going to cut cut cut cut but I'm going to stop before I cross that line now I won't be fully cut through on the bottom because the blade is round if you've cut anything you you kind of understand that concept so then I can take my whether it's a Handa or jigsaw or whatever I can take this plunge it in and finish those cuts out reason I want to do that is I don't want to overcut slightly with the circular saw so that this falls out because then I I create a weaker Stringer okay I think that will make more sense once I do it uh something else that I'll mention is you always want to have at least 3 and 1/2 Ines after you've cut these Out 3 and 1 half inches of strength in here left of your Stringer we've got lots we're going to be about five um we probably could have got away with 2 by10 just barely but I'd rather be stronger than than not so okay so I'm going to bring this down and I'm going to make this stopped okay so now you can see that piece still is in there I I could hit it and it would fall out or whatever it' break out but there' still be a little chunk left back in there in fact maybe that's what I'll do I'll show you what's left so I knock that out of there and if I flip this up you can see I've got this little piece up there little triangle that didn't come out so that's what I've got to that's what I've got to cut out this other okay so now I've got that all cut out of there nice and square okay you need you need that to be nice and and a nice square cut so then I'm just going to continue along cutting all these out and then when I get to the end we'll uh show you exactly what I do with the with that end uh cut that we talked about at the floor okay here's the bottom of my stringer at the floor and this is the floor

Auto-generated transcript. May contain errors.