Skip to main content

Mark the Stringers and Adjust for Treads — Mark the Stair Stringer with a Framing Square

Beginner4 hours

Part of project

How to Lay Out a Stair Stringer with a Framing Square · Step 4 of 6

Helpful?

In this video

Begin marking the stringer. The video suggests starting from one end of the board and marking the first riser cut to maximize material. Then, flip the framing square to mark the first tread angle. For subsequent steps, carefully align the square by placing the previous marked line perpendicular to the edge of the square at the 10-inch mark. This ensures accuracy, as relying solely on visual alignment can lead to errors due to natural inconsistencies in lumber. Continue marking the triangles for each step along the entire length of the stringer. As a beginner, it's easy to forget to account for the thickness of the first tread. To correct this, the first riser should be reduced by 1 1/2 inches (the thickness of a 2x material). For example, if your riser is 7 3/8 inches, the first riser cut should be 5 7/8 inches. The top step also needs consideration to ensure it's not too short. For added precision, the video suggests using a nail to create a tick mark at the exact corner of each step's layout. This tick mark will serve as a consistent reference point when moving the square or using a tape measure to verify distances. Use a construction calculator to find the diagonal length of each step (e.g., 7 3/8" rise, 10" run gives 12 7/16" diagonal). Then, use a tape measure to mark these cumulative diagonal distances along the bottom edge of the stringer. This visual check confirms the accuracy of your square markings.

2.4M views31.8K
stairbuilding

75K subscribers

View Channel

FAQs

What is the most critical tool for ensuring accurate stair stringer layout?

The framing square, especially when used with stair gauges, is indispensable for consistently marking the rise and run on the stringer. A construction calculator is also highly recommended to minimize mathematical errors and ensure precise measurements.

How important is accuracy when marking a stair stringer, and what are the safety implications?

Accuracy is paramount for safety; even small errors can lead to uneven steps, creating a significant tripping hazard. Double-check all measurements and markings before cutting, as consistent riser heights and tread depths are crucial to prevent falls.

Can I use different materials for stair stringers, or is pressure-treated pine always necessary?

While pressure-treated pine is excellent for outdoor use or areas prone to moisture, untreated lumber like Douglas fir or Southern Yellow Pine can be used for indoor stairs. Always select straight, knot-free lumber of appropriate dimensions that meets local building codes for structural integrity.

What's a common mistake beginners make when laying out stringers, and how can I avoid it?

A frequent error is forgetting to account for the thickness of the treads and the necessary bottom cut for the finished floor. Ensure you deduct the tread thickness from the bottom riser and factor in the nosing overhang for consistent steps from top to bottom.

Transcript
Hide

run now what I do and I've already done this one so I'm going to show you here on this other board first thing is I like to maximize my material so I'm gonna come in here and just give myself an arbitrary first riser okay this is the angle of my first step the face of my first step and you'll notice all I did was flipped around my square still on the same dimensions and it's going to give me that angle now when I rotate it back okay I'm gonna have to move this one second now when I flip it back over remember I've got that set at ten and seven and three-eighths all I'm gonna do is line up this edge at ten right where this thing comes in perpendicular don't always go off of your eye where you think it's supposed to be and move this far over if you see what just happened it looks like I'm right in line to be on a perfect perfect connection to this corner but because material is kind of rounded and weird it's always nice to just make sure that your ten inch like that is perpendicular perfect to the line that you've just made and all you're gonna do is you're gonna come in here and you're gonna make your little triangle this is what's going to get cut out for your stare and it's gonna be ten inch seven and three-eighths one thing that I want you to know is that when determining your stair layout I said you have to know all of your final dimensions because this first step if I just go ahead and cut it at 7 and three-eighths okay and I make this the bottom that's on the ground what's gonna happen is I'm gonna go ahead and put another two by twelve right here the two by twelve is gonna sit here for my first step now this rise is actually nine eight eight and seven eighths of an inch we don't want that so with that being said you have to consider your first step you have to take an inch and a half off of your seven and three eighths so if I was at seven and three-eighths and I'm gonna go - an inch and a half and I can just do this pretty easily here by doing inch and a half you have to you have to make sure that you figure that and this is the thing that I always messed up as a beginner as I would always forget to subtract my bottom and I would end up having too tall of the first step and same goes with the top remember at 1/10 and a half that's my top finished floor you have to remember that because otherwise you'll have to potentially short of a top step so we're gonna go ahead and lay this out really quickly but I'm going to show you another tip that will help…

Auto-generated transcript. May contain errors.