Skip to main content

Diagnose and Rebuild Irrigation Control Valve — Repair or Replace Faulty Valves

Beginner4 hours

Part of project

Irrigation System Repair · Step 6 of 10

Helpful?

In this video

Locate the irrigation control valve box, typically buried near the affected zone. Carefully remove the lid and clear away any debris or spiderwebs to get a clear view of the valves and wiring. Identify the valve that is leaking (often indicated by persistent dampness, mud, or even plant roots growing directly from the leak point). To rebuild the valve, first disconnect the solenoid by unscrewing it. Then, use a small Phillips head screwdriver to unscrew the multiple screws holding the top housing of the valve in place. Carefully lift off the top, exposing the diaphragm. Remove the old diaphragm and check for any debris (like rocks or sediment) that might be preventing a proper seal. Clean the area thoroughly and install the new diaphragm from a Rain Bird rebuild kit (DRK-CP/CPF), ensuring it is seated correctly. Reattach the top housing by screwing it back in, and then re-install the solenoid. Test the system to ensure the leak is resolved.

33.4K views1.7K
The Handyman

532K subscribers

View Channel

FAQs

What specialized tools are essential for irrigation system repair beyond general household tools?

You'll definitely need a good shovel for digging, especially around pipes without damaging them. A hook and pick set is invaluable for cleaning stubborn sprinkler nozzles, and an adjustable wrench will help with various fittings. Don't forget PVC primer and cement for pipe repairs, and Teflon tape for threaded connections.

My sprinkler zone isn't turning on at all. Where should I start troubleshooting?

First, verify the zone is programmed correctly on your controller and that the master valve (if you have one) is open. Then, locate the valve for the non-working zone. Manually turn the solenoid a quarter turn counter-clockwise or flip its lever to see if the sprinklers activate, which helps isolate if the issue is electrical or mechanical within the valve itself.

How can I pinpoint an underground leak without excavating my entire lawn?

Look for unusually wet or overly green spots in your yard, or areas where the grass is unusually lush. You can also listen for hissing sounds near the main line or check your water meter for continuous movement even when all water sources are off, indicating a constant flow.

What are the most important safety precautions to take when digging for underground irrigation repairs?

Always call 811 (or your local 'dig safe' number) a few days before you dig to have underground utility lines marked. Wear sturdy gloves to protect your hands from debris and tools. Dig carefully and by hand when you get close to pipes or marked lines to avoid damaging them or other utilities.

Transcript
Hide

here we're going to call that a win woo so here is the next problem the valve is leaking just a little bit a little trickle some serious spider action down in these things not sure how well this is going to show or not cuz it's kind of dark in this hole but there's Roots literally growing out of the valve the valve and the PVC pipe this is the one that has that very slow leak I might get lucky I just turned it off an extra e to a/ quter turn that's what these do here that's why they all have levers on them so you can open them up and close them and turn your zones on manually so I just got a little extra turn on this and I'm going to go check it out maybe that's all it took to turn it off I don't think I'm going to get that lucky I never do really get that lucky this is a very very slow leak but you can see see those clear swirls of water coming up out of the dirty water there you can see it it's almost like a freshwater spring coming up out of a out of the ground I'm just going to go rebuild the valve and it's going to take a couple days to see if it actually stopped the flow of water through here this is the rebuild kit just a replacement diaphragm there's not much more in these not sure how well you guys are going to be able to see down in there but these screws are up against the plastic housing so I'm using this little this little thing to get in there and it is actually working to get those close screws out already unscrewed the selenoid show you what that looks like this right here make sure you don't lose any of the parts or the gaskets why couldn't it have been one of the middle valves you know that'll be the one that's all the way cranked over to the edge next time you're in Harbor Freight make sure you go pick up one of these pick sets Pittsburgh super cheap very useful little diaphragm is off what is that what is that I see a piece of going to go wash this off and then there's one other piece that goes in the solenoid and that's it we put it back together and it's

Auto-generated transcript. May contain errors.