Skip to main content

Cut and Install the Skirt Board — Cut the Skirt Board

Beginner4 hours

Part of project

How to Scribe and Cut a Stair Skirt Board to Fit · Step 3 of 5

Helpful?

In this video

Once all horizontal and vertical lines representing the stair profile are clearly marked on the temporary board, carefully detach it from the wall or stair stringer. Using an appropriate saw (e.g., jigsaw, circular saw, or handsaw), precisely cut along the marked lines. After cutting, position the newly cut skirt board (which is now the finished piece) into its final desired location against the staircase. If you observe any small, unacceptable gaps (e.g., at the inner corners where the riser meets the tread), you can carefully raise the entire skirt board slightly. The 'insurance' measurement added in the previous step should provide enough material to allow for this minor vertical adjustment, ensuring a tight fit at all points. This final adjustment eliminates any remaining small gaps caused by subtle imperfections in the existing stairs.

131.2K views1.4K
Inside Carpentry

321K subscribers

View Channel

FAQs

What specific tools are essential for accurately scribing a stair skirt board?

The Bullet Tools Stair Step Scribe 2 is crucial for transferring the exact stair profile to your skirt board, ensuring a snug fit. A good quality pencil for marking and a reliable measuring tape are also indispensable for precise measurements. For cutting, a jigsaw will be your primary tool for intricate angles.

Is this project truly beginner-friendly, and can it be completed within the estimated 4 hours?

While rated beginner, patience and precision are key. The scribing and cutting steps require careful attention, and mistakes can be costly. For a first-timer, 4 hours might be tight, especially if you need to troubleshoot or make small adjustments. Allow for extra time, particularly for dry fitting and fine-tuning cuts.

What's the biggest mistake beginners make when cutting the skirt board, and how can it be avoided?

The most common mistake is cutting too much material, as you can't add it back. Always cut slightly outside your scribe line and then use a block plane or sandpaper to slowly shave down to the line for a perfect fit. Remember the adage, "Measure twice, cut once," and apply it rigorously to this project.

Can I use materials other than cellular PVC for the skirt board, and what are the pros and cons?

Yes, solid wood (like pine or oak) or MDF are common alternatives. Cellular PVC, like the Veranda trim suggested, offers excellent moisture resistance and stability, making it good for varying humidity. Wood can be stained to match existing trim but may be more prone to warping or shrinking if not properly acclimated before installation.

Transcript
Hide

And then do the same to the rest of the steps. So I should end up with something like this. And after I've marked everything, it wouldn't be a bad idea to see if we have any spots like this because this is going to provide us with a little gap that might not be acceptable to some of you. And if this is the case, all you need to do is raise all of the lines a little bit and that'll be all of the lines for all of the steps. So you can see here where it's a little different than it is down below. And here it looks like we have a bigger gap and all you're doing is compensating for the variations in the steps to make your skirt board work. So hopefully that makes sense because after you've laid everything out, you can go ahead and detach your template or your skirt board so that you can cut it and then after it has been cut, you can go ahead and position it in place. So again, I kind of left this here on purpose to give you an idea of what could happen if you don't increase the measurement a little bit for your template. And you don't have to go a quarter of an inch. You can always go a half inch or three quarters of an inch just to make sure. And of course, it's all going to depend upon how much room you need here, the distance between the top of the skirt board and the corner of the steps. And hopefully all of that made sense. However, if it did not, feel free to leave any questions you have in the comment area and I will answer them as soon as possible.

Auto-generated transcript. May contain errors.