Disconnect Water Supply Line — Prepare Work Area and Shut Off Water
Part of project
How to Fix a Leak at a Faucet Supply Line Connection · Step 1 of 5
In this video
First, locate the water shutoff valve (angle stop) under the sink. Turn the handle clockwise until it stops to shut off the water supply. Using a pair of adjustable pliers, grip the nut connecting the braided supply line to the valve and turn it counter-clockwise to loosen and remove the line. Have a small towel ready to catch any dripping water.
Goal: Remove existing supply line from the shutoff valve.
- Water may drip from the disconnected line, so place a towel or small bucket underneath.
Used in this video
- Adjustable Pliers (Pliers_Type: Channel-Lock) — Loosening the supply line nut from the valve.
- Towel — Catching residual water.
719K subscribers
FAQs
How long does a beginner typically need to fix a faucet supply line leak, and what's the most common hold-up?
For most beginners, this project takes about 30-60 minutes. The biggest time-consumer is often preparing the work area, ensuring the water is fully off, and carefully tightening the new connections to avoid overtightening or cross-threading.
The project mentions a 'Braided Polymer Faucet Supply Line.' Are there other types, and how do I ensure I get the right replacement?
Yes, supply lines come in various materials like braided stainless steel or PEX, which are also durable options. The most critical step is to match the length and the connector sizes (e.g., 3/8 in. compression x 1/2 in. FIP) of your new line to your existing one and the connections on your faucet and shut-off valve.
I've replaced the supply line, but it's still leaking slightly after installation. What's the first thing I should check?
First, ensure both nuts are snug but not overtightened; over-tightening can damage internal washers or threads. Confirm the supply line is seated straight without cross-threading, and visually check that the small rubber washer inside the faucet connection is present and intact, as this creates the primary seal.
Is it ever okay to just tighten the old leaky supply line connection instead of replacing the entire line?
You can attempt a slight turn with your wrench to see if it stops the leak, but if it's an older line or already tight, this often isn't a permanent fix and could worsen the leak. Replacing the inexpensive supply line ensures a fresh, reliable seal, especially if the internal washers are worn or compressed.
Disconnect Water Supply Line — Prepare Work Area and Shut Off Water
Part of project
How to Fix a Leak at a Faucet Supply Line Connection · Step 1 of 5
In this video
First, locate the water shutoff valve (angle stop) under the sink. Turn the handle clockwise until it stops to shut off the water supply. Using a pair of adjustable pliers, grip the nut connecting the braided supply line to the valve and turn it counter-clockwise to loosen and remove the line. Have a small towel ready to catch any dripping water.
Goal: Remove existing supply line from the shutoff valve.
- Water may drip from the disconnected line, so place a towel or small bucket underneath.
Used in this video
- Adjustable Pliers (Pliers_Type: Channel-Lock) — Loosening the supply line nut from the valve.
- Towel — Catching residual water.
Frequently Asked Questions
How long does a beginner typically need to fix a faucet supply line leak, and what's the most common hold-up?
For most beginners, this project takes about 30-60 minutes. The biggest time-consumer is often preparing the work area, ensuring the water is fully off, and carefully tightening the new connections to avoid overtightening or cross-threading.
The project mentions a 'Braided Polymer Faucet Supply Line.' Are there other types, and how do I ensure I get the right replacement?
Yes, supply lines come in various materials like braided stainless steel or PEX, which are also durable options. The most critical step is to match the length and the connector sizes (e.g., 3/8 in. compression x 1/2 in. FIP) of your new line to your existing one and the connections on your faucet and shut-off valve.
I've replaced the supply line, but it's still leaking slightly after installation. What's the first thing I should check?
First, ensure both nuts are snug but not overtightened; over-tightening can damage internal washers or threads. Confirm the supply line is seated straight without cross-threading, and visually check that the small rubber washer inside the faucet connection is present and intact, as this creates the primary seal.
Is it ever okay to just tighten the old leaky supply line connection instead of replacing the entire line?
You can attempt a slight turn with your wrench to see if it stops the leak, but if it's an older line or already tight, this often isn't a permanent fix and could worsen the leak. Replacing the inexpensive supply line ensures a fresh, reliable seal, especially if the internal washers are worn or compressed.