Ignite the Pilot Flame — Light the Pilot Light
Part of project
How to Safely Relight Your Gas Water Heater Pilot Light · Step 6 of 10
In this video
With the control knob set to 'Pilot', press and hold down the red pilot button. While continuously holding the button, use a long-reach lighter to carefully introduce a flame to the end of the pilot tube inside the burner chamber. You will see a small blue flame ignite. Continue to hold the red button down for approximately 30-60 seconds. This allows the thermocouple to heat up, which is a safety device that will keep the pilot lit after you release the button.
Goal: Successfully light the pilot and heat the thermocouple.
- You must keep the pilot button fully depressed while lighting and holding the flame.
Used in this video
- Long-reach lighter — Safely introducing a flame into the burner chamber to ignite the pilot light.
150K subscribers
FAQs
What should I do if I smell gas strongly before or during the relighting process?
This is a critical safety concern. If you smell gas, immediately stop, evacuate everyone from the house, and call your gas company's emergency line from outside. Do not attempt to relight the pilot, use any electrical switches, or operate anything that could create a spark.
Can I use a standard match or a short lighter instead of the recommended long flexible lighter?
While it might seem possible, it's highly recommended to use a long, flexible lighter like the Bernzomatic LTR220. This keeps your hands safely away from the burner area and any potential flare-ups, significantly reducing the risk of burns. Prioritize safety with the right tools.
My pilot light lights up, but goes out as soon as I release the gas control knob. What could be wrong?
This usually indicates a faulty thermocouple, which is a safety device that senses the pilot flame. Try holding the knob in longer (up to 60 seconds) to ensure the thermocouple heats sufficiently. If it still won't stay lit, the thermocouple likely needs replacement, which is a slightly more advanced DIY task or a job for a professional.
How long does this project typically take for a beginner, and is it truly considered 'beginner' difficulty?
For a true beginner, this project generally takes about 30-45 minutes, especially if you take your time with all the safety steps. It is considered beginner-friendly because it primarily involves following clear instructions and basic tool use, with the main challenge being careful adherence to safety protocols.
TranscriptHide
Auto-generated transcript. May contain errors.
Ignite the Pilot Flame — Light the Pilot Light
Part of project
How to Safely Relight Your Gas Water Heater Pilot Light · Step 6 of 10
In this video
With the control knob set to 'Pilot', press and hold down the red pilot button. While continuously holding the button, use a long-reach lighter to carefully introduce a flame to the end of the pilot tube inside the burner chamber. You will see a small blue flame ignite. Continue to hold the red button down for approximately 30-60 seconds. This allows the thermocouple to heat up, which is a safety device that will keep the pilot lit after you release the button.
Goal: Successfully light the pilot and heat the thermocouple.
- You must keep the pilot button fully depressed while lighting and holding the flame.
Used in this video
- Long-reach lighter — Safely introducing a flame into the burner chamber to ignite the pilot light.
Frequently Asked Questions
What should I do if I smell gas strongly before or during the relighting process?
This is a critical safety concern. If you smell gas, immediately stop, evacuate everyone from the house, and call your gas company's emergency line from outside. Do not attempt to relight the pilot, use any electrical switches, or operate anything that could create a spark.
Can I use a standard match or a short lighter instead of the recommended long flexible lighter?
While it might seem possible, it's highly recommended to use a long, flexible lighter like the Bernzomatic LTR220. This keeps your hands safely away from the burner area and any potential flare-ups, significantly reducing the risk of burns. Prioritize safety with the right tools.
My pilot light lights up, but goes out as soon as I release the gas control knob. What could be wrong?
This usually indicates a faulty thermocouple, which is a safety device that senses the pilot flame. Try holding the knob in longer (up to 60 seconds) to ensure the thermocouple heats sufficiently. If it still won't stay lit, the thermocouple likely needs replacement, which is a slightly more advanced DIY task or a job for a professional.
How long does this project typically take for a beginner, and is it truly considered 'beginner' difficulty?
For a true beginner, this project generally takes about 30-45 minutes, especially if you take your time with all the safety steps. It is considered beginner-friendly because it primarily involves following clear instructions and basic tool use, with the main challenge being careful adherence to safety protocols.
Video Transcript
(289 characters)Hide
Video Transcript
(289 characters)Transcript may be auto-generated and contain errors.