Access the Heating Elements — Access the Pilot Light Assembly
Part of project
How to Safely Relight Your Gas Water Heater Pilot Light · Step 3 of 10
In this video
Using a screwdriver, remove the screws securing the upper and lower access panels on the front of the water heater. Set the panels and screws aside. Carefully pull out the pieces of fiberglass insulation that are behind the panels. Finally, remove the plastic safety guard that covers the thermostat and the element's terminal screws.
Goal: Expose Heating Elements
- Keep the screws with their corresponding panels to avoid misplacing them.
Used in this video
- Screwdriver (Tool Type: Hand Tools) — To remove the screws holding the access panels in place.
150K subscribers
FAQs
What should I do if I smell gas strongly before or during the relighting process?
This is a critical safety concern. If you smell gas, immediately stop, evacuate everyone from the house, and call your gas company's emergency line from outside. Do not attempt to relight the pilot, use any electrical switches, or operate anything that could create a spark.
Can I use a standard match or a short lighter instead of the recommended long flexible lighter?
While it might seem possible, it's highly recommended to use a long, flexible lighter like the Bernzomatic LTR220. This keeps your hands safely away from the burner area and any potential flare-ups, significantly reducing the risk of burns. Prioritize safety with the right tools.
My pilot light lights up, but goes out as soon as I release the gas control knob. What could be wrong?
This usually indicates a faulty thermocouple, which is a safety device that senses the pilot flame. Try holding the knob in longer (up to 60 seconds) to ensure the thermocouple heats sufficiently. If it still won't stay lit, the thermocouple likely needs replacement, which is a slightly more advanced DIY task or a job for a professional.
How long does this project typically take for a beginner, and is it truly considered 'beginner' difficulty?
For a true beginner, this project generally takes about 30-45 minutes, especially if you take your time with all the safety steps. It is considered beginner-friendly because it primarily involves following clear instructions and basic tool use, with the main challenge being careful adherence to safety protocols.
TranscriptHide
Auto-generated transcript. May contain errors.
Access the Heating Elements — Access the Pilot Light Assembly
Part of project
How to Safely Relight Your Gas Water Heater Pilot Light · Step 3 of 10
In this video
Using a screwdriver, remove the screws securing the upper and lower access panels on the front of the water heater. Set the panels and screws aside. Carefully pull out the pieces of fiberglass insulation that are behind the panels. Finally, remove the plastic safety guard that covers the thermostat and the element's terminal screws.
Goal: Expose Heating Elements
- Keep the screws with their corresponding panels to avoid misplacing them.
Used in this video
- Screwdriver (Tool Type: Hand Tools) — To remove the screws holding the access panels in place.
Frequently Asked Questions
What should I do if I smell gas strongly before or during the relighting process?
This is a critical safety concern. If you smell gas, immediately stop, evacuate everyone from the house, and call your gas company's emergency line from outside. Do not attempt to relight the pilot, use any electrical switches, or operate anything that could create a spark.
Can I use a standard match or a short lighter instead of the recommended long flexible lighter?
While it might seem possible, it's highly recommended to use a long, flexible lighter like the Bernzomatic LTR220. This keeps your hands safely away from the burner area and any potential flare-ups, significantly reducing the risk of burns. Prioritize safety with the right tools.
My pilot light lights up, but goes out as soon as I release the gas control knob. What could be wrong?
This usually indicates a faulty thermocouple, which is a safety device that senses the pilot flame. Try holding the knob in longer (up to 60 seconds) to ensure the thermocouple heats sufficiently. If it still won't stay lit, the thermocouple likely needs replacement, which is a slightly more advanced DIY task or a job for a professional.
How long does this project typically take for a beginner, and is it truly considered 'beginner' difficulty?
For a true beginner, this project generally takes about 30-45 minutes, especially if you take your time with all the safety steps. It is considered beginner-friendly because it primarily involves following clear instructions and basic tool use, with the main challenge being careful adherence to safety protocols.
Video Transcript
(58 characters)Hide
Video Transcript
(58 characters)Transcript may be auto-generated and contain errors.