Cap Outlet and Pressure Test — Turn On Water and Test for Leaks
Part of project
How to Replace a Deck-Mount Garden Tub Faucet · Step 8 of 9
In this video
Before turning on the water supply to test for leaks, you must cap the shower head outlet. Take a threaded pipe nipple and an end cap. Apply Teflon tape to the threads of the nipple, then screw on the end cap and tighten with a wrench. Screw this capped nipple into the drop-ear elbow where the shower arm will eventually go. Once capped, you can slowly turn the main water supply back on and carefully inspect every connection point (at the valve and the drop-ear elbow) for any signs of dripping or leaks.
Goal: Test all new plumbing connections for leaks
- Do not skip this step. It is critical to identify and fix leaks before closing up the wall.
Used in this video
- Adjustable Wrench (Tool Type: Hand Tools, Power Source: Manual) — Tightening the end cap onto the pipe nipple.
671K subscribers
FAQs
Is this project truly intermediate, and what are the main challenges I might face?
Yes, this project is rated intermediate due to the tight spaces often found under garden tubs, potential corrosion on old fasteners, and the critical need for watertight seals. Expect to spend significant time gaining access, maneuvering tools, and meticulously checking for leaks. Patience and preparation are key.
My old faucet seems stuck or corroded to the deck. What's the best way to loosen it?
Corrosion is common. Apply a penetrating oil like KROIL directly to the nuts under the tub deck and allow it to soak for at least 30 minutes, or even an hour. Use a basin wrench for extra leverage in tight spots, as it's designed for these hard-to-reach fittings.
What are the most common reasons for leaks after installing a new deck-mount faucet, and how can I prevent them?
Leaks typically occur from improperly sealed connections or loose fittings. Always apply 2-3 wraps of Teflon tape clockwise to all threaded pipe connections before tightening. For the faucet body, ensure you use a generous but neat amount of plumber's putty around the base to create a watertight seal against the tub deck.
My tub's access panel seems too small or is difficult to open. What should I do if I can't reach the plumbing easily?
Gaining proper access is crucial and sometimes the most challenging part. Use a headlamp for visibility and consider temporarily removing any surrounding trim or cabinet components if necessary. If space is extremely limited, you might need to carefully enlarge the access opening, ensuring it can be neatly covered afterward.
Cap Outlet and Pressure Test — Turn On Water and Test for Leaks
Part of project
How to Replace a Deck-Mount Garden Tub Faucet · Step 8 of 9
In this video
Before turning on the water supply to test for leaks, you must cap the shower head outlet. Take a threaded pipe nipple and an end cap. Apply Teflon tape to the threads of the nipple, then screw on the end cap and tighten with a wrench. Screw this capped nipple into the drop-ear elbow where the shower arm will eventually go. Once capped, you can slowly turn the main water supply back on and carefully inspect every connection point (at the valve and the drop-ear elbow) for any signs of dripping or leaks.
Goal: Test all new plumbing connections for leaks
- Do not skip this step. It is critical to identify and fix leaks before closing up the wall.
Used in this video
- Adjustable Wrench (Tool Type: Hand Tools, Power Source: Manual) — Tightening the end cap onto the pipe nipple.
Frequently Asked Questions
Is this project truly intermediate, and what are the main challenges I might face?
Yes, this project is rated intermediate due to the tight spaces often found under garden tubs, potential corrosion on old fasteners, and the critical need for watertight seals. Expect to spend significant time gaining access, maneuvering tools, and meticulously checking for leaks. Patience and preparation are key.
My old faucet seems stuck or corroded to the deck. What's the best way to loosen it?
Corrosion is common. Apply a penetrating oil like KROIL directly to the nuts under the tub deck and allow it to soak for at least 30 minutes, or even an hour. Use a basin wrench for extra leverage in tight spots, as it's designed for these hard-to-reach fittings.
What are the most common reasons for leaks after installing a new deck-mount faucet, and how can I prevent them?
Leaks typically occur from improperly sealed connections or loose fittings. Always apply 2-3 wraps of Teflon tape clockwise to all threaded pipe connections before tightening. For the faucet body, ensure you use a generous but neat amount of plumber's putty around the base to create a watertight seal against the tub deck.
My tub's access panel seems too small or is difficult to open. What should I do if I can't reach the plumbing easily?
Gaining proper access is crucial and sometimes the most challenging part. Use a headlamp for visibility and consider temporarily removing any surrounding trim or cabinet components if necessary. If space is extremely limited, you might need to carefully enlarge the access opening, ensuring it can be neatly covered afterward.