Connect Water Supply Lines — Connect New Plumbing Lines
Part of project
How to Replace a Deck-Mount Garden Tub Faucet · Step 7 of 9
In this video
To ensure a watertight seal, wrap Teflon tape clockwise around the male threads of your hot and cold water supply valves under the sink. Connect the corresponding braided hot and cold supply lines from the new faucet to these valves. Hand-tighten the connections first, and then use an adjustable wrench to give them a final, snug turn, typically about a quarter-turn past hand-tight.
Goal: Connect Water Supply
- Be careful not to over-tighten the connections, as this can damage the fittings and cause leaks.
Used in this video
- Adjustable Wrench (Tool Type: Hand Tools, Wrench Type: Adjustable wrench) — Tightening the water supply line connections.
671K subscribers
FAQs
Is this project truly intermediate, and what are the main challenges I might face?
Yes, this project is rated intermediate due to the tight spaces often found under garden tubs, potential corrosion on old fasteners, and the critical need for watertight seals. Expect to spend significant time gaining access, maneuvering tools, and meticulously checking for leaks. Patience and preparation are key.
My old faucet seems stuck or corroded to the deck. What's the best way to loosen it?
Corrosion is common. Apply a penetrating oil like KROIL directly to the nuts under the tub deck and allow it to soak for at least 30 minutes, or even an hour. Use a basin wrench for extra leverage in tight spots, as it's designed for these hard-to-reach fittings.
What are the most common reasons for leaks after installing a new deck-mount faucet, and how can I prevent them?
Leaks typically occur from improperly sealed connections or loose fittings. Always apply 2-3 wraps of Teflon tape clockwise to all threaded pipe connections before tightening. For the faucet body, ensure you use a generous but neat amount of plumber's putty around the base to create a watertight seal against the tub deck.
My tub's access panel seems too small or is difficult to open. What should I do if I can't reach the plumbing easily?
Gaining proper access is crucial and sometimes the most challenging part. Use a headlamp for visibility and consider temporarily removing any surrounding trim or cabinet components if necessary. If space is extremely limited, you might need to carefully enlarge the access opening, ensuring it can be neatly covered afterward.
Connect Water Supply Lines — Connect New Plumbing Lines
Part of project
How to Replace a Deck-Mount Garden Tub Faucet · Step 7 of 9
In this video
To ensure a watertight seal, wrap Teflon tape clockwise around the male threads of your hot and cold water supply valves under the sink. Connect the corresponding braided hot and cold supply lines from the new faucet to these valves. Hand-tighten the connections first, and then use an adjustable wrench to give them a final, snug turn, typically about a quarter-turn past hand-tight.
Goal: Connect Water Supply
- Be careful not to over-tighten the connections, as this can damage the fittings and cause leaks.
Used in this video
- Adjustable Wrench (Tool Type: Hand Tools, Wrench Type: Adjustable wrench) — Tightening the water supply line connections.
Frequently Asked Questions
Is this project truly intermediate, and what are the main challenges I might face?
Yes, this project is rated intermediate due to the tight spaces often found under garden tubs, potential corrosion on old fasteners, and the critical need for watertight seals. Expect to spend significant time gaining access, maneuvering tools, and meticulously checking for leaks. Patience and preparation are key.
My old faucet seems stuck or corroded to the deck. What's the best way to loosen it?
Corrosion is common. Apply a penetrating oil like KROIL directly to the nuts under the tub deck and allow it to soak for at least 30 minutes, or even an hour. Use a basin wrench for extra leverage in tight spots, as it's designed for these hard-to-reach fittings.
What are the most common reasons for leaks after installing a new deck-mount faucet, and how can I prevent them?
Leaks typically occur from improperly sealed connections or loose fittings. Always apply 2-3 wraps of Teflon tape clockwise to all threaded pipe connections before tightening. For the faucet body, ensure you use a generous but neat amount of plumber's putty around the base to create a watertight seal against the tub deck.
My tub's access panel seems too small or is difficult to open. What should I do if I can't reach the plumbing easily?
Gaining proper access is crucial and sometimes the most challenging part. Use a headlamp for visibility and consider temporarily removing any surrounding trim or cabinet components if necessary. If space is extremely limited, you might need to carefully enlarge the access opening, ensuring it can be neatly covered afterward.