Reconnect Faucet and Drain — Mount the New Faucet
Part of project
How to Replace a Deck-Mount Garden Tub Faucet · Step 6 of 9
In this video
Attach the faucet's mounting block to the new tub. Slide the faucet onto the block and tighten the screw. For the drain, use the new slip nut and gasket that came with the tub. Place the slip nut on the tailpiece, followed by the gasket with the beveled edge facing down towards the fitting. Thread this assembly onto the bottom of the sink. Then, connect the P-trap, ensuring all slip nuts are hand-tightened.
Goal: Connect plumbing to the new sink
- Ensure the drain gasket's beveled edge faces the fitting it's sealing against to prevent leaks.
- Do not use tools to tighten plastic nuts; hand-tight is sufficient and prevents cracking.
Used in this video
- Screwdriver (brand: Generic, Tool Type: Hand tools, Power Source: Manual) — Tightening the faucet mounting screw.
671K subscribers
FAQs
Is this project truly intermediate, and what are the main challenges I might face?
Yes, this project is rated intermediate due to the tight spaces often found under garden tubs, potential corrosion on old fasteners, and the critical need for watertight seals. Expect to spend significant time gaining access, maneuvering tools, and meticulously checking for leaks. Patience and preparation are key.
My old faucet seems stuck or corroded to the deck. What's the best way to loosen it?
Corrosion is common. Apply a penetrating oil like KROIL directly to the nuts under the tub deck and allow it to soak for at least 30 minutes, or even an hour. Use a basin wrench for extra leverage in tight spots, as it's designed for these hard-to-reach fittings.
What are the most common reasons for leaks after installing a new deck-mount faucet, and how can I prevent them?
Leaks typically occur from improperly sealed connections or loose fittings. Always apply 2-3 wraps of Teflon tape clockwise to all threaded pipe connections before tightening. For the faucet body, ensure you use a generous but neat amount of plumber's putty around the base to create a watertight seal against the tub deck.
My tub's access panel seems too small or is difficult to open. What should I do if I can't reach the plumbing easily?
Gaining proper access is crucial and sometimes the most challenging part. Use a headlamp for visibility and consider temporarily removing any surrounding trim or cabinet components if necessary. If space is extremely limited, you might need to carefully enlarge the access opening, ensuring it can be neatly covered afterward.
Reconnect Faucet and Drain — Mount the New Faucet
Part of project
How to Replace a Deck-Mount Garden Tub Faucet · Step 6 of 9
In this video
Attach the faucet's mounting block to the new tub. Slide the faucet onto the block and tighten the screw. For the drain, use the new slip nut and gasket that came with the tub. Place the slip nut on the tailpiece, followed by the gasket with the beveled edge facing down towards the fitting. Thread this assembly onto the bottom of the sink. Then, connect the P-trap, ensuring all slip nuts are hand-tightened.
Goal: Connect plumbing to the new sink
- Ensure the drain gasket's beveled edge faces the fitting it's sealing against to prevent leaks.
- Do not use tools to tighten plastic nuts; hand-tight is sufficient and prevents cracking.
Used in this video
- Screwdriver (brand: Generic, Tool Type: Hand tools, Power Source: Manual) — Tightening the faucet mounting screw.
Frequently Asked Questions
Is this project truly intermediate, and what are the main challenges I might face?
Yes, this project is rated intermediate due to the tight spaces often found under garden tubs, potential corrosion on old fasteners, and the critical need for watertight seals. Expect to spend significant time gaining access, maneuvering tools, and meticulously checking for leaks. Patience and preparation are key.
My old faucet seems stuck or corroded to the deck. What's the best way to loosen it?
Corrosion is common. Apply a penetrating oil like KROIL directly to the nuts under the tub deck and allow it to soak for at least 30 minutes, or even an hour. Use a basin wrench for extra leverage in tight spots, as it's designed for these hard-to-reach fittings.
What are the most common reasons for leaks after installing a new deck-mount faucet, and how can I prevent them?
Leaks typically occur from improperly sealed connections or loose fittings. Always apply 2-3 wraps of Teflon tape clockwise to all threaded pipe connections before tightening. For the faucet body, ensure you use a generous but neat amount of plumber's putty around the base to create a watertight seal against the tub deck.
My tub's access panel seems too small or is difficult to open. What should I do if I can't reach the plumbing easily?
Gaining proper access is crucial and sometimes the most challenging part. Use a headlamp for visibility and consider temporarily removing any surrounding trim or cabinet components if necessary. If space is extremely limited, you might need to carefully enlarge the access opening, ensuring it can be neatly covered afterward.