Reassemble the Faucet
Part of project
Fix a Leaky Faucet: Troubleshooting Faulty Water Intake · Step 4 of 5
This DIY project, "Fix a Leaky Faucet: Troubleshooting Faulty Water Intake," guides you through the steps of repairing a compression faucet leak. It begins by instructing you to turn off both hot and cold water supply lines under the sink. Next, the faucet is disassembled, starting with removing the handle screws (often under decorative caps) and then the handles themselves, followed by the packing nut and stem. Pictures taken during disassembly will help with reassembly. The project then details replacing any worn O-rings and washers, applying plumber's grease to new O-rings for a proper seal. The faucet is carefully reassembled, reversing the disassembly steps. Finally, the water supply is slowly turned back on and the faucet is checked for any remaining leaks. If leaks persist, connections should be re-tightened or faulty components replaced.
1.1M subscribers
FAQs
What should I do if I can't locate or turn off the hot and cold water supply lines under the sink?
If the shut-off valves under your sink are inaccessible or seized, you must locate and turn off the main water supply to your entire house before proceeding. Never attempt faucet disassembly with the water supply still on, as this can lead to significant flooding and water damage. Once the main supply is off, open a lower-level faucet to drain the remaining water from the pipes.
Are the specified tools (Adjustable Wrench, Phillips head screwdriver) the only ones I'll need, or should I have others on hand?
While the adjustable wrench and Phillips head screwdriver are essential, it's also helpful to have a small flathead screwdriver or utility knife for prying off decorative caps. A set of O-ring picks can make removing old O-rings easier, and a wire brush can be useful for cleaning mineral deposits on internal components. Having a rag or small bucket ready for drips is also a good idea.
My faucet is still leaking after I've followed all the steps and reassembled it. What should I check next?
If the leak persists, carefully re-tighten all connections, ensuring they are snug but not overtightened, which can damage parts. Double-check that the new O-rings and washers are correctly sized, seated properly, and that plumber's grease was applied. Sometimes, the faucet seat itself might be worn or corroded, requiring a specific seat wrench for repair or replacement.
How do I ensure I get the correct replacement O-rings and washers for my specific faucet model?
The best way to get the correct replacement parts is to take the old O-rings and washers with you to a hardware store to match them for size and material. Alternatively, if you know your faucet's brand and model number, you can often find a repair kit or parts list online. Always apply plumber's grease to new O-rings for a better seal and extended life.
Reassemble the Faucet
Part of project
Fix a Leaky Faucet: Troubleshooting Faulty Water Intake · Step 4 of 5
This DIY project, "Fix a Leaky Faucet: Troubleshooting Faulty Water Intake," guides you through the steps of repairing a compression faucet leak. It begins by instructing you to turn off both hot and cold water supply lines under the sink. Next, the faucet is disassembled, starting with removing the handle screws (often under decorative caps) and then the handles themselves, followed by the packing nut and stem. Pictures taken during disassembly will help with reassembly. The project then details replacing any worn O-rings and washers, applying plumber's grease to new O-rings for a proper seal. The faucet is carefully reassembled, reversing the disassembly steps. Finally, the water supply is slowly turned back on and the faucet is checked for any remaining leaks. If leaks persist, connections should be re-tightened or faulty components replaced.
Frequently Asked Questions
What should I do if I can't locate or turn off the hot and cold water supply lines under the sink?
If the shut-off valves under your sink are inaccessible or seized, you must locate and turn off the main water supply to your entire house before proceeding. Never attempt faucet disassembly with the water supply still on, as this can lead to significant flooding and water damage. Once the main supply is off, open a lower-level faucet to drain the remaining water from the pipes.
Are the specified tools (Adjustable Wrench, Phillips head screwdriver) the only ones I'll need, or should I have others on hand?
While the adjustable wrench and Phillips head screwdriver are essential, it's also helpful to have a small flathead screwdriver or utility knife for prying off decorative caps. A set of O-ring picks can make removing old O-rings easier, and a wire brush can be useful for cleaning mineral deposits on internal components. Having a rag or small bucket ready for drips is also a good idea.
My faucet is still leaking after I've followed all the steps and reassembled it. What should I check next?
If the leak persists, carefully re-tighten all connections, ensuring they are snug but not overtightened, which can damage parts. Double-check that the new O-rings and washers are correctly sized, seated properly, and that plumber's grease was applied. Sometimes, the faucet seat itself might be worn or corroded, requiring a specific seat wrench for repair or replacement.
How do I ensure I get the correct replacement O-rings and washers for my specific faucet model?
The best way to get the correct replacement parts is to take the old O-rings and washers with you to a hardware store to match them for size and material. Alternatively, if you know your faucet's brand and model number, you can often find a repair kit or parts list online. Always apply plumber's grease to new O-rings for a better seal and extended life.