Shut off cold water supply — Shut Off the Water Supply
Part of project
Delta Shower Handle Replacement: A Step-by-Step DIY Guide · Step 1 of 4
In this video
Shut off the cold water supply to the water heater. Find the water valve located on the cold water supply line feeding the water heater and turn it clockwise to shut off the water.
Goal: Stop the flow of water coming into the tank
- If the valve is difficult to turn, use a wrench or pliers to apply more leverage, but be careful not to damage the valve.
Used in this video
- Adjustable wrench · optional — Turning the main water valve if difficult.
1.3M subscribers
FAQs
Do I need the specific Milwaukee screwdriver mentioned, or will any flathead and Phillips head screwdriver work for this project?
While the Milwaukee screwdriver is a good quality tool, any standard flathead and Phillips head screwdriver of the appropriate size will work. Ensure the screwdriver tip matches the screw head size to prevent stripping the screws during removal or installation, which is a common issue.
What should I do if I can't shut off the water supply to just the shower, or if water continues to drip after shutting it off?
If you can't isolate the shower's water supply, you'll need to turn off the main water supply to your entire house, usually found near the water meter or main shut-off valve. If water still drips after turning off the supply, double-check that the valve is fully closed. For persistent drips, you might need to address the shut-off valve itself or consult a plumber before proceeding.
My old Delta handle's screw cover is stuck or won't come off easily. How can I remove it without causing damage?
Often, old screw covers can be stiff due to mineral buildup. Try gently prying around the edges with a thin, flat tool like a plastic putty knife or the edge of a flathead screwdriver wrapped in painter's tape to avoid scratching. If it's still stuck, a small amount of penetrating lubricant applied carefully around the edge might help loosen it, but wipe away any excess immediately.
Is 45 minutes a realistic time estimate for a complete beginner, or should I budget more time for this Delta handle replacement?
The 45-minute estimate is generally realistic for someone with basic DIY skills and the right tools on hand. However, as a complete beginner, it's wise to budget an hour or two. This allows for potential issues like stuck screws, locating your main water shut-off, or needing extra time to review instructions carefully.
TranscriptHide
Auto-generated transcript. May contain errors.
Shut off cold water supply — Shut Off the Water Supply
Part of project
Delta Shower Handle Replacement: A Step-by-Step DIY Guide · Step 1 of 4
In this video
Shut off the cold water supply to the water heater. Find the water valve located on the cold water supply line feeding the water heater and turn it clockwise to shut off the water.
Goal: Stop the flow of water coming into the tank
- If the valve is difficult to turn, use a wrench or pliers to apply more leverage, but be careful not to damage the valve.
Used in this video
- Adjustable wrench · optional — Turning the main water valve if difficult.
Frequently Asked Questions
Do I need the specific Milwaukee screwdriver mentioned, or will any flathead and Phillips head screwdriver work for this project?
While the Milwaukee screwdriver is a good quality tool, any standard flathead and Phillips head screwdriver of the appropriate size will work. Ensure the screwdriver tip matches the screw head size to prevent stripping the screws during removal or installation, which is a common issue.
What should I do if I can't shut off the water supply to just the shower, or if water continues to drip after shutting it off?
If you can't isolate the shower's water supply, you'll need to turn off the main water supply to your entire house, usually found near the water meter or main shut-off valve. If water still drips after turning off the supply, double-check that the valve is fully closed. For persistent drips, you might need to address the shut-off valve itself or consult a plumber before proceeding.
My old Delta handle's screw cover is stuck or won't come off easily. How can I remove it without causing damage?
Often, old screw covers can be stiff due to mineral buildup. Try gently prying around the edges with a thin, flat tool like a plastic putty knife or the edge of a flathead screwdriver wrapped in painter's tape to avoid scratching. If it's still stuck, a small amount of penetrating lubricant applied carefully around the edge might help loosen it, but wipe away any excess immediately.
Is 45 minutes a realistic time estimate for a complete beginner, or should I budget more time for this Delta handle replacement?
The 45-minute estimate is generally realistic for someone with basic DIY skills and the right tools on hand. However, as a complete beginner, it's wise to budget an hour or two. This allows for potential issues like stuck screws, locating your main water shut-off, or needing extra time to review instructions carefully.
Video Transcript
(117 characters)Hide
Video Transcript
(117 characters)Transcript may be auto-generated and contain errors.