Reassemble the Stopper and Pivot Rod — Clean Drain and Prepare New Stopper
Part of project
How to Remove and Replace a Bathroom Sink Pop-Up Stopper · Step 4 of 7
In this video
Place the cleaned stopper back into the sink drain opening, making sure the loop on the bottom of the stopper is facing towards the back of the sink. From underneath, carefully slide the pivot rod back into its opening on the drain pipe. The end of the rod must pass through the stopper's loop. You may need to jiggle the stopper from above to help align it. Once the rod is correctly positioned through the loop, screw the retaining nut back on and hand-tighten it to secure the pivot rod.
Goal: Reinstall the sink stopper and connect the pivot rod
- Aligning the pivot rod with the stopper loop can be tricky. Having a helper jiggle the stopper from above can make this step much easier.
841K subscribers
FAQs
How difficult is it to replace a bathroom sink pop-up stopper for a beginner, and how long should it take?
This project is rated as 'beginner' difficulty. For most DIYers, it should take about 30 minutes to an hour, assuming no major complications like rusted or seized parts. Taking your time to understand the linkage and ensuring a good seal will prevent future issues.
What are the most common problems I might encounter when replacing the stopper, and how can I avoid them?
The most common issues are leaks after reassembly and difficulty with the pivot rod. To avoid leaks, ensure all connections, especially the nut holding the pivot rod, are tightened properly but not overtightened. If the old pivot rod is stuck, apply penetrating oil and let it sit before trying to remove it gently with your Husky 10 in. Quick Adjusting Groove Joint Pliers.
Do I need all the specific tools listed, like the Husky groove joint pliers or the Flateye flashlight?
While specific brands aren't mandatory, having a good pair of adjustable pliers (like groove joint or channel locks) is crucial for loosening nuts under the sink. A bright, hands-free flashlight, such as the Panther Vision FLATEYE, is also highly recommended as lighting under a sink cabinet is usually poor. These tools will make the job significantly easier and safer.
How can I prevent water leaks after installing the new pop-up stopper?
The key to preventing leaks is ensuring the new stopper assembly, especially the part that goes through the drain opening, is properly sealed. Most new stoppers come with gaskets, but applying a small bead of plumber's putty around the underside of the drain flange before inserting it can provide an extra layer of protection. Always test by filling the sink and letting it drain slowly, checking for drips immediately after installation using WYPALL L40 Towels.
Reassemble the Stopper and Pivot Rod — Clean Drain and Prepare New Stopper
Part of project
How to Remove and Replace a Bathroom Sink Pop-Up Stopper · Step 4 of 7
In this video
Place the cleaned stopper back into the sink drain opening, making sure the loop on the bottom of the stopper is facing towards the back of the sink. From underneath, carefully slide the pivot rod back into its opening on the drain pipe. The end of the rod must pass through the stopper's loop. You may need to jiggle the stopper from above to help align it. Once the rod is correctly positioned through the loop, screw the retaining nut back on and hand-tighten it to secure the pivot rod.
Goal: Reinstall the sink stopper and connect the pivot rod
- Aligning the pivot rod with the stopper loop can be tricky. Having a helper jiggle the stopper from above can make this step much easier.
Frequently Asked Questions
How difficult is it to replace a bathroom sink pop-up stopper for a beginner, and how long should it take?
This project is rated as 'beginner' difficulty. For most DIYers, it should take about 30 minutes to an hour, assuming no major complications like rusted or seized parts. Taking your time to understand the linkage and ensuring a good seal will prevent future issues.
What are the most common problems I might encounter when replacing the stopper, and how can I avoid them?
The most common issues are leaks after reassembly and difficulty with the pivot rod. To avoid leaks, ensure all connections, especially the nut holding the pivot rod, are tightened properly but not overtightened. If the old pivot rod is stuck, apply penetrating oil and let it sit before trying to remove it gently with your Husky 10 in. Quick Adjusting Groove Joint Pliers.
Do I need all the specific tools listed, like the Husky groove joint pliers or the Flateye flashlight?
While specific brands aren't mandatory, having a good pair of adjustable pliers (like groove joint or channel locks) is crucial for loosening nuts under the sink. A bright, hands-free flashlight, such as the Panther Vision FLATEYE, is also highly recommended as lighting under a sink cabinet is usually poor. These tools will make the job significantly easier and safer.
How can I prevent water leaks after installing the new pop-up stopper?
The key to preventing leaks is ensuring the new stopper assembly, especially the part that goes through the drain opening, is properly sealed. Most new stoppers come with gaskets, but applying a small bead of plumber's putty around the underside of the drain flange before inserting it can provide an extra layer of protection. Always test by filling the sink and letting it drain slowly, checking for drips immediately after installation using WYPALL L40 Towels.