Disassemble Tool and Inspect Pipe — Remove the Old Angle Stop
Part of project
How to Replace a Leaky Angle Stop (Shutoff Valve) Under Your Sink · Step 4 of 8
In this video
After the sleeve has been pulled off the pipe, turn the T-handle counter-clockwise to release the tool's internal pressure. Unscrew the puller's cap from the compression nut. The tool can now be removed, along with the freed compression nut and sleeve. Inspect the copper pipe to ensure it is smooth and undamaged, ready for the installation of a new valve.
Goal: Remove tool and inspect results
- Use a deburring tool or some fine-grit sandpaper to clean up the end of the copper pipe if there are any rough edges.
Used in this video
- Compression Sleeve Puller (Tool Type: Pipe wrench) — Disassembling the tool after the extraction is complete.
201K subscribers
FAQs
How difficult is it to replace an angle stop, and how long does it typically take for a beginner?
This project is rated as 'beginner' difficulty, making it accessible for most DIYers. While shutting off water and working in tight spaces requires attention, the steps are straightforward. Expect to spend around 3 hours, which includes time for preparation, troubleshooting, and thorough leak testing.
What are the most important safety precautions I need to take before starting this plumbing repair?
The most critical step is to shut off the main water supply to your house to prevent potential flooding. Always have a bucket and plenty of absorbent towels like WYPALL L40 or ITOPFOX paper towels readily available for draining residual water and catching any spills. Good lighting, such as the Panther Vision FLATEYE flashlight, is also essential for working under the sink.
Do I really need specialized plumbing tools for this project, or can I get by with basic household tools?
While some tools listed are general, an adjustable wrench and quality tongue-and-groove pliers (like Channellock 430) are essential for securely tightening and loosening plumbing connections. These specialized tools provide the necessary grip and leverage to prevent stripping fasteners or damaging pipes, which household tools might struggle with.
What's the most common reason for a new angle stop to leak after installation, and how can I prevent it?
The most common reason for a leak is improper tightening of the compression nut or an uneven/burred pipe end. Ensure the copper pipe is clean and smooth, free of any imperfections, before sliding on the new compression components. Tighten the compression nut firmly with an adjustable wrench, but avoid overtightening, as this can damage the ferrule; a slight weep often just needs another quarter turn.
Disassemble Tool and Inspect Pipe — Remove the Old Angle Stop
Part of project
How to Replace a Leaky Angle Stop (Shutoff Valve) Under Your Sink · Step 4 of 8
In this video
After the sleeve has been pulled off the pipe, turn the T-handle counter-clockwise to release the tool's internal pressure. Unscrew the puller's cap from the compression nut. The tool can now be removed, along with the freed compression nut and sleeve. Inspect the copper pipe to ensure it is smooth and undamaged, ready for the installation of a new valve.
Goal: Remove tool and inspect results
- Use a deburring tool or some fine-grit sandpaper to clean up the end of the copper pipe if there are any rough edges.
Used in this video
- Compression Sleeve Puller (Tool Type: Pipe wrench) — Disassembling the tool after the extraction is complete.
Frequently Asked Questions
How difficult is it to replace an angle stop, and how long does it typically take for a beginner?
This project is rated as 'beginner' difficulty, making it accessible for most DIYers. While shutting off water and working in tight spaces requires attention, the steps are straightforward. Expect to spend around 3 hours, which includes time for preparation, troubleshooting, and thorough leak testing.
What are the most important safety precautions I need to take before starting this plumbing repair?
The most critical step is to shut off the main water supply to your house to prevent potential flooding. Always have a bucket and plenty of absorbent towels like WYPALL L40 or ITOPFOX paper towels readily available for draining residual water and catching any spills. Good lighting, such as the Panther Vision FLATEYE flashlight, is also essential for working under the sink.
Do I really need specialized plumbing tools for this project, or can I get by with basic household tools?
While some tools listed are general, an adjustable wrench and quality tongue-and-groove pliers (like Channellock 430) are essential for securely tightening and loosening plumbing connections. These specialized tools provide the necessary grip and leverage to prevent stripping fasteners or damaging pipes, which household tools might struggle with.
What's the most common reason for a new angle stop to leak after installation, and how can I prevent it?
The most common reason for a leak is improper tightening of the compression nut or an uneven/burred pipe end. Ensure the copper pipe is clean and smooth, free of any imperfections, before sliding on the new compression components. Tighten the compression nut firmly with an adjustable wrench, but avoid overtightening, as this can damage the ferrule; a slight weep often just needs another quarter turn.