Drain Water from the Tank — Drain Water Heater (if replacing element)
Part of project
Fix a Water Heater: No Hot Water Troubleshooting · Step 4 of 4
In this video
Locate the drain valve at the bottom of the water heater. Attach a garden hose to the valve and run the other end to a floor drain or a bucket. Open the drain valve to let water out of the tank. You only need to drain enough water so that the water level is below the T&P valve you are replacing.
Goal: Lower Water Level
- The water coming out of the drain valve can be extremely hot. Use a heat-rated hose and handle with care.
Used in this video
- Garden Hose — Directing water from the drain valve to a drain or bucket.
- Bucket · optional — Collecting water if a floor drain is not available.
662K subscribers
FAQs
What are the most critical safety precautions I need to take before starting this water heater troubleshooting project?
The absolute first steps are to turn off the power to the water heater at your electrical panel and shut off the cold water supply valve to the tank. Always use a non-contact voltage tester to confirm the power is off at the element terminals before touching any wires to prevent electrical shock. This prioritization of safety prevents serious injury or property damage.
Do I really need a multimeter for this project, and how does it help diagnose the problem?
Yes, a multimeter is essential for accurately diagnosing if the heating element is faulty. You'll set it to measure resistance (ohms) and touch the leads to the element's screw terminals. A reading between 10-30 ohms indicates the element is likely good, while an "OL" (Open Line) reading means it's broken and needs replacement.
When do I need to drain the entire water heater tank, and when is it not necessary?
You only need to drain the water heater tank if you determine the heating element is faulty and you plan to replace it. If you are just performing the diagnostic test on the element and it proves to be functional, there is no need to drain the tank. Draining can add significant time to the project, so avoid it if not necessary.
My multimeter displayed "OL" when I tested the heating element; what does this signify, and what's my next step?
An "OL" (Open Line) reading on your multimeter indicates that the heating element has an open circuit, meaning it's faulty and needs to be replaced. Your next step is to proceed with draining the tank, disconnecting the old element, and installing a new one. Be sure to purchase a replacement element that matches your water heater's specifications.
Drain Water from the Tank — Drain Water Heater (if replacing element)
Part of project
Fix a Water Heater: No Hot Water Troubleshooting · Step 4 of 4
In this video
Locate the drain valve at the bottom of the water heater. Attach a garden hose to the valve and run the other end to a floor drain or a bucket. Open the drain valve to let water out of the tank. You only need to drain enough water so that the water level is below the T&P valve you are replacing.
Goal: Lower Water Level
- The water coming out of the drain valve can be extremely hot. Use a heat-rated hose and handle with care.
Used in this video
- Garden Hose — Directing water from the drain valve to a drain or bucket.
- Bucket · optional — Collecting water if a floor drain is not available.
Frequently Asked Questions
What are the most critical safety precautions I need to take before starting this water heater troubleshooting project?
The absolute first steps are to turn off the power to the water heater at your electrical panel and shut off the cold water supply valve to the tank. Always use a non-contact voltage tester to confirm the power is off at the element terminals before touching any wires to prevent electrical shock. This prioritization of safety prevents serious injury or property damage.
Do I really need a multimeter for this project, and how does it help diagnose the problem?
Yes, a multimeter is essential for accurately diagnosing if the heating element is faulty. You'll set it to measure resistance (ohms) and touch the leads to the element's screw terminals. A reading between 10-30 ohms indicates the element is likely good, while an "OL" (Open Line) reading means it's broken and needs replacement.
When do I need to drain the entire water heater tank, and when is it not necessary?
You only need to drain the water heater tank if you determine the heating element is faulty and you plan to replace it. If you are just performing the diagnostic test on the element and it proves to be functional, there is no need to drain the tank. Draining can add significant time to the project, so avoid it if not necessary.
My multimeter displayed "OL" when I tested the heating element; what does this signify, and what's my next step?
An "OL" (Open Line) reading on your multimeter indicates that the heating element has an open circuit, meaning it's faulty and needs to be replaced. Your next step is to proceed with draining the tank, disconnecting the old element, and installing a new one. Be sure to purchase a replacement element that matches your water heater's specifications.