Skip to main content
Stesso
Project

Test and Adjust — Test and Adjust the New Fill Valve

Beginner2 hours

Part of project

Fix Leaky Toilets: A Step-by-Step Guide to Replacing Your Fill Valve · Step 5 of 6

Helpful?

In this video

Slowly turn the water supply back on and check for leaks. Adjust the water level in the tank using the adjustment screw on the fill valve and adjust the water level in the bowl by adjusting the water supply hose.

Goal: Ensure proper water levels in both tank and bowl

  • The water level in the tank should be just below the top of the overflow tube. The water level in the bowl should be at the desired level without spilling into the overflow tube. Be sure to tighten the lock ring on the fill valve to prevent issues when adjusting.

Used in this video

  • Adjustable Wrench · optional — Adjusting water level in bowl
  • Pliers · optional — Adjusting water level in bowl
157.8K views1.1K5 minutes
replumb

719K subscribers

View Channel

FAQs

My new fill valve is leaking where it connects to the water supply line. What should I check?

First, ensure the connection is hand-tightened, then gently snug it with your adjustable wrench, being careful not to overtighten and strip the threads. Also, check that the rubber washer inside the coupling is properly seated and not pinched or missing; a new washer may be needed if it's damaged.

Is replacing a toilet fill valve truly a beginner-friendly project, and how much time should I set aside?

Yes, this project is very beginner-friendly and perfect for a first-time DIYer. Most people can complete the entire process, including preparation and testing, within 1 to 2 hours. Taking your time and carefully following each step will help ensure a successful repair.

What crucial safety precautions should I take before starting this toilet repair?

Always begin by turning off the water supply to the toilet, usually via a small shut-off valve at the wall or floor. After turning it off, flush the toilet to empty the tank as much as possible to minimize water spills when you disconnect lines and remove the old valve.

Besides an adjustable wrench, are there any other tools I might need for this project?

An adjustable wrench, like the Husky 12 in. Adjustable Wrench, is the primary tool you'll need. You might also find a bucket helpful to catch any residual water from the tank or supply line, and a sponge or old towel for easy cleanup of small spills.

Transcript
Hide

the overflow tube you can add your hose and this hose supplies water to the bowl at this point you're ready to start cracking the water so you can fill up and test the operation and see if you're going to need to adjust the water level which i am going to need to adjust the water level on this one you see that green line on the overflow tube that's where we want the water level to stop and in this case it's stopping way too short there are fine tune adjustments that you can do on this knob here but it's not going to be enough to get me about an inch and a half so i'm actually going to have to lift the fill valve up about an inch which is going to require me to shut the water off again because you do not want to do this adjustment with pressure behind the fill valve you can actually do this adjustment even before you put this in but it can be done after the fact there's a ring at the bottom here you need to loosen up and then you can lift the fill valve up and then lock that ring back down it is extremely important to make sure that that ring locks again so you want to give the fill valve a tug in the upward direction and make sure that you cannot lift it up again before you turn your water back on otherwise the fill valve can shoot off the top and you'll have a geyser in your bathroom so right now i'm gonna need to do a little bit of a fine tuning on this because it's shutting off just above that green line so there's a plus and a minus arrow on this adjustment here so you can just follow the directions and get the water level exactly where you want it you want to have it right where it says that way you get the optimal flush after you have the optimal flush achieved you can adjust the water level in the bowl with this valve here you can leave it straight in line with the hose to put the most water in the bowl or you can close it off to leave a little bit of water in the bowl the way you want to do it is you want to have it basically fill up just to the point where the bowl is full and not overflowing into the trap takes a little bit of practice but there is a sweet spot on these things i'm gonna be doing

Auto-generated transcript. May contain errors.