Remove Old Angle Stop — Remove Old Ferrule and Clean Pipe
Part of project
How to Replace a Leaky Angle Stop (Shutoff Valve) Under Your Sink · Step 4 of 6
In this video
Use an adjustable wrench or angle stop wrench to loosen and remove the nut behind the old compression angle stop. If possible, avoid replacing the existing nut because the ferrule (a small ring used to create a seal) underneath it can get squished around the copper pipe, making removal difficult without specialized tools like a ferrule puller or a small handsaw.
Goal: Detach the old angle stop
- Be careful not to damage the surrounding area or pipes.
- If necessary, use a small handsaw or ferrule puller to remove the nut.
Used in this video
- Angle Stop Wrench (Tool Type: Adjustable wrench, Power Source: Manual, Material Compatibility: Copper, Size/Capacity: Small, Durability: High, Cost: Medium) — Loosening and tightening the nut behind the angle stop.
944K subscribers
FAQs
How long should I expect this project to take for a beginner, and what's the overall difficulty level?
This is a beginner-friendly plumbing project, typically taking 30-60 minutes once you have all the tools and materials ready. The most crucial steps involve ensuring the water supply is off and achieving a watertight seal.
What's the most crucial safety step I need to take before starting to avoid major water damage?
The most crucial step is to fully shut off the main water supply to your home before you begin any work. After turning it off, open a faucet on a lower level to confirm water flow has completely stopped and to drain the lines.
Do I really need a specific type of adjustable wrench, or will any adjustable wrench work for this project?
While the 12-inch adjustable wrench listed provides good leverage, any sturdy adjustable wrench that can securely grip the compression nuts will work. Ensure it's in good condition to prevent slipping and damage.
What is the most common mistake beginners make when installing a new compression angle stop, and how can I avoid it?
The most common mistake is overtightening or undertightening the compression nut, leading to leaks or damaging the valve/pipe. Tighten the nut until it feels snug, then give it an additional quarter to half turn, being careful not to strip threads.
Remove Old Angle Stop — Remove Old Ferrule and Clean Pipe
Part of project
How to Replace a Leaky Angle Stop (Shutoff Valve) Under Your Sink · Step 4 of 6
In this video
Use an adjustable wrench or angle stop wrench to loosen and remove the nut behind the old compression angle stop. If possible, avoid replacing the existing nut because the ferrule (a small ring used to create a seal) underneath it can get squished around the copper pipe, making removal difficult without specialized tools like a ferrule puller or a small handsaw.
Goal: Detach the old angle stop
- Be careful not to damage the surrounding area or pipes.
- If necessary, use a small handsaw or ferrule puller to remove the nut.
Used in this video
- Angle Stop Wrench (Tool Type: Adjustable wrench, Power Source: Manual, Material Compatibility: Copper, Size/Capacity: Small, Durability: High, Cost: Medium) — Loosening and tightening the nut behind the angle stop.
Frequently Asked Questions
How long should I expect this project to take for a beginner, and what's the overall difficulty level?
This is a beginner-friendly plumbing project, typically taking 30-60 minutes once you have all the tools and materials ready. The most crucial steps involve ensuring the water supply is off and achieving a watertight seal.
What's the most crucial safety step I need to take before starting to avoid major water damage?
The most crucial step is to fully shut off the main water supply to your home before you begin any work. After turning it off, open a faucet on a lower level to confirm water flow has completely stopped and to drain the lines.
Do I really need a specific type of adjustable wrench, or will any adjustable wrench work for this project?
While the 12-inch adjustable wrench listed provides good leverage, any sturdy adjustable wrench that can securely grip the compression nuts will work. Ensure it's in good condition to prevent slipping and damage.
What is the most common mistake beginners make when installing a new compression angle stop, and how can I avoid it?
The most common mistake is overtightening or undertightening the compression nut, leading to leaks or damaging the valve/pipe. Tighten the nut until it feels snug, then give it an additional quarter to half turn, being careful not to strip threads.