Shut Off Water Supply and Drain Line — Shut Off Main Water Supply and Drain Lines
Part of project
How to Replace a Leaky Angle Stop (Shutoff Valve) Under Your Sink · Step 1 of 6
In this video
Locate the main water shut-off valve for your home, which is often found in a utility closet, basement, or garage near the water meter. Turn the valve handle completely to shut off the water supply. Then, go back to the outdoor faucet and open it to allow any remaining water in the pipe to drain out completely.
Goal: Prepare for Repair
- Failing to shut off the water will result in uncontrolled water flow when you disassemble the faucet.
Used in this video
- Main Water Shut-off Valve — Shutting off the water supply to the entire house.
944K subscribers
FAQs
How long should I expect this project to take for a beginner, and what's the overall difficulty level?
This is a beginner-friendly plumbing project, typically taking 30-60 minutes once you have all the tools and materials ready. The most crucial steps involve ensuring the water supply is off and achieving a watertight seal.
What's the most crucial safety step I need to take before starting to avoid major water damage?
The most crucial step is to fully shut off the main water supply to your home before you begin any work. After turning it off, open a faucet on a lower level to confirm water flow has completely stopped and to drain the lines.
Do I really need a specific type of adjustable wrench, or will any adjustable wrench work for this project?
While the 12-inch adjustable wrench listed provides good leverage, any sturdy adjustable wrench that can securely grip the compression nuts will work. Ensure it's in good condition to prevent slipping and damage.
What is the most common mistake beginners make when installing a new compression angle stop, and how can I avoid it?
The most common mistake is overtightening or undertightening the compression nut, leading to leaks or damaging the valve/pipe. Tighten the nut until it feels snug, then give it an additional quarter to half turn, being careful not to strip threads.
Shut Off Water Supply and Drain Line — Shut Off Main Water Supply and Drain Lines
Part of project
How to Replace a Leaky Angle Stop (Shutoff Valve) Under Your Sink · Step 1 of 6
In this video
Locate the main water shut-off valve for your home, which is often found in a utility closet, basement, or garage near the water meter. Turn the valve handle completely to shut off the water supply. Then, go back to the outdoor faucet and open it to allow any remaining water in the pipe to drain out completely.
Goal: Prepare for Repair
- Failing to shut off the water will result in uncontrolled water flow when you disassemble the faucet.
Used in this video
- Main Water Shut-off Valve — Shutting off the water supply to the entire house.
Frequently Asked Questions
How long should I expect this project to take for a beginner, and what's the overall difficulty level?
This is a beginner-friendly plumbing project, typically taking 30-60 minutes once you have all the tools and materials ready. The most crucial steps involve ensuring the water supply is off and achieving a watertight seal.
What's the most crucial safety step I need to take before starting to avoid major water damage?
The most crucial step is to fully shut off the main water supply to your home before you begin any work. After turning it off, open a faucet on a lower level to confirm water flow has completely stopped and to drain the lines.
Do I really need a specific type of adjustable wrench, or will any adjustable wrench work for this project?
While the 12-inch adjustable wrench listed provides good leverage, any sturdy adjustable wrench that can securely grip the compression nuts will work. Ensure it's in good condition to prevent slipping and damage.
What is the most common mistake beginners make when installing a new compression angle stop, and how can I avoid it?
The most common mistake is overtightening or undertightening the compression nut, leading to leaks or damaging the valve/pipe. Tighten the nut until it feels snug, then give it an additional quarter to half turn, being careful not to strip threads.