Remove the Old Regulator — Remove the Old Angle Stop
Part of project
How to Replace a Leaky Angle Stop (Shutoff Valve) Under Your Sink · Step 4 of 10
In this video
With the water off, use the channel-lock pliers to grip the body of the old regulator or the adjacent pipe to hold it steady. Use the large pipe wrench to turn the union nuts on both the inlet and outlet sides counter-clockwise to loosen them. Once loose, unscrew them by hand. Be prepared for some residual water to spill out. After both sides are disconnected, lift the old regulator out of the pipe line.
Goal: Disconnect and remove the old plumbing fixture
Used in this video
- Pipe wrench (brand: Husky, Tool Type: Hand Tools) — Loosening the union nuts.
- Channel-Lock Pliers (brand: Husky, Tool Type: Hand Tools) — Providing a backup grip to prevent pipes from twisting.
89K subscribers
FAQs
What should I do if the old compression nut and ferrule are seized onto the copper pipe?
Apply penetrating oil, like Blaster PB Penetrating Oil, directly to the nut and ferrule. Allow it to soak for 15-30 minutes before attempting to loosen it again with your adjustable wrench. If it's still stuck, you may need to carefully cut the old ferrule off with a small hacksaw or specialized tool, taking care not to damage the copper pipe itself.
How can I prevent leaks after installing the new angle stop?
Ensure the copper pipe is clean, smooth, and free of burrs or scratches where the new ferrule will sit. Hand-tighten the compression nut first, then use your adjustable wrench to tighten it an additional half to three-quarters of a turn. Avoid overtightening, as this can damage the ferrule or pipe, but ensure it's snug enough to prevent drips.
Do I really need to shut off the main water supply for this project?
Yes, absolutely. Shutting off the main water supply is crucial to prevent significant flooding when you remove the old valve. Always relieve any remaining water pressure by opening a nearby faucet after shutting off the main supply, before starting work under the sink.
How long should this project typically take for a beginner?
For a DIY beginner, expect this project to take approximately 1 to 2 hours. This accounts for time to gather tools, carefully follow each step, and troubleshoot minor issues like a stubborn old valve or initial small leaks. Taking your time will help ensure a successful installation.
Remove the Old Regulator — Remove the Old Angle Stop
Part of project
How to Replace a Leaky Angle Stop (Shutoff Valve) Under Your Sink · Step 4 of 10
In this video
With the water off, use the channel-lock pliers to grip the body of the old regulator or the adjacent pipe to hold it steady. Use the large pipe wrench to turn the union nuts on both the inlet and outlet sides counter-clockwise to loosen them. Once loose, unscrew them by hand. Be prepared for some residual water to spill out. After both sides are disconnected, lift the old regulator out of the pipe line.
Goal: Disconnect and remove the old plumbing fixture
Used in this video
- Pipe wrench (brand: Husky, Tool Type: Hand Tools) — Loosening the union nuts.
- Channel-Lock Pliers (brand: Husky, Tool Type: Hand Tools) — Providing a backup grip to prevent pipes from twisting.
Frequently Asked Questions
What should I do if the old compression nut and ferrule are seized onto the copper pipe?
Apply penetrating oil, like Blaster PB Penetrating Oil, directly to the nut and ferrule. Allow it to soak for 15-30 minutes before attempting to loosen it again with your adjustable wrench. If it's still stuck, you may need to carefully cut the old ferrule off with a small hacksaw or specialized tool, taking care not to damage the copper pipe itself.
How can I prevent leaks after installing the new angle stop?
Ensure the copper pipe is clean, smooth, and free of burrs or scratches where the new ferrule will sit. Hand-tighten the compression nut first, then use your adjustable wrench to tighten it an additional half to three-quarters of a turn. Avoid overtightening, as this can damage the ferrule or pipe, but ensure it's snug enough to prevent drips.
Do I really need to shut off the main water supply for this project?
Yes, absolutely. Shutting off the main water supply is crucial to prevent significant flooding when you remove the old valve. Always relieve any remaining water pressure by opening a nearby faucet after shutting off the main supply, before starting work under the sink.
How long should this project typically take for a beginner?
For a DIY beginner, expect this project to take approximately 1 to 2 hours. This accounts for time to gather tools, carefully follow each step, and troubleshoot minor issues like a stubborn old valve or initial small leaks. Taking your time will help ensure a successful installation.