Connect and Tighten the Pipe Connection — Install the New Angle Stop
Part of project
How to Replace a Leaky Angle Stop (Shutoff Valve) Under Your Sink · Step 6 of 8
In this video
Align the copper pipe with the new valve's connection point. Hand-tighten the compression nut with the applied sealant onto the valve. Once hand-tight, use two wrenches to fully tighten the connection. Use one wrench to hold the valve body steady and the other to tighten the compression nut. Ensure the connection is snug but avoid over-tightening, which can damage the fittings.
Goal: Securely connect the copper pipe to the new valve.
Used in this video
- Locking Pliers (brand: Vise-Grip, Tool Type: Pliers, Pliers_Type: Channel-Lock, Material: Metal, Size/Dimension: Medium) — Holding the valve body steady during tightening.
- Open-End Wrench (Tool Type: Wrench, Wrench Type: Open-end, Material: Metal, Size/Dimension: Medium) — Tightening the compression nut onto the valve.
17K subscribers
FAQs
What's the most critical safety step before beginning the angle stop replacement?
The most critical step is always to shut off the main water supply to your house completely, not just the valve under the sink. This prevents potential flooding and ensures no water pressure is present while you're working on the pipe.
How long should a beginner expect this project to take, and what is the approximate cost?
For a beginner, this project typically takes 1 to 2 hours, allowing time for preparation and careful leak checks. The material cost is relatively low, mainly for the new angle stop and a new supply line, usually ranging from $20 to $40.
What tools do I need beyond basic wrenches for this project?
While adjustable wrenches and pliers are essential, 150-grit sandpaper is crucial for cleaning the copper pipe to ensure a good seal. You'll also need a bucket for draining water and plenty of absorbent towels (like WYPALL L40 or Scott Rags) to manage spills.
What's a common mistake beginners make that can lead to leaks after installation?
A common mistake is not thoroughly cleaning and preparing the copper pipe surface before installing the new compression fitting. Ensure the pipe is smooth, free of burrs, and clear of old compression ring residue using 150-grit sandpaper for a watertight seal.
Connect and Tighten the Pipe Connection — Install the New Angle Stop
Part of project
How to Replace a Leaky Angle Stop (Shutoff Valve) Under Your Sink · Step 6 of 8
In this video
Align the copper pipe with the new valve's connection point. Hand-tighten the compression nut with the applied sealant onto the valve. Once hand-tight, use two wrenches to fully tighten the connection. Use one wrench to hold the valve body steady and the other to tighten the compression nut. Ensure the connection is snug but avoid over-tightening, which can damage the fittings.
Goal: Securely connect the copper pipe to the new valve.
Used in this video
- Locking Pliers (brand: Vise-Grip, Tool Type: Pliers, Pliers_Type: Channel-Lock, Material: Metal, Size/Dimension: Medium) — Holding the valve body steady during tightening.
- Open-End Wrench (Tool Type: Wrench, Wrench Type: Open-end, Material: Metal, Size/Dimension: Medium) — Tightening the compression nut onto the valve.
Frequently Asked Questions
What's the most critical safety step before beginning the angle stop replacement?
The most critical step is always to shut off the main water supply to your house completely, not just the valve under the sink. This prevents potential flooding and ensures no water pressure is present while you're working on the pipe.
How long should a beginner expect this project to take, and what is the approximate cost?
For a beginner, this project typically takes 1 to 2 hours, allowing time for preparation and careful leak checks. The material cost is relatively low, mainly for the new angle stop and a new supply line, usually ranging from $20 to $40.
What tools do I need beyond basic wrenches for this project?
While adjustable wrenches and pliers are essential, 150-grit sandpaper is crucial for cleaning the copper pipe to ensure a good seal. You'll also need a bucket for draining water and plenty of absorbent towels (like WYPALL L40 or Scott Rags) to manage spills.
What's a common mistake beginners make that can lead to leaks after installation?
A common mistake is not thoroughly cleaning and preparing the copper pipe surface before installing the new compression fitting. Ensure the pipe is smooth, free of burrs, and clear of old compression ring residue using 150-grit sandpaper for a watertight seal.