Refill the Water Heater — Refill Tank and Check for Leaks
Part of project
How to Replace a Water Heater's T&P Relief Valve · Step 7 of 8
In this video
To refill the tank, first ensure the hot water faucet you opened earlier is still open. This allows air to escape as the tank fills. Then, fully open the cold water inlet shut-off valve. You will hear the tank begin to fill with water. While it's filling, check the new drain valve for any leaks or drips. Keep the hot water faucet open until a steady stream of water flows out, which indicates the tank is full of water and all the air has been purged. Once you have a steady stream, you can turn the faucet off.
Goal: Fill Tank with Water
- Check the new drain valve to make sure there are no leaks or drips as the tank fills.
662K subscribers
FAQs
Is replacing a T&P relief valve a safe DIY project for a beginner, or should I call a professional?
This is a beginner-level plumbing task, but only if you strictly follow all safety procedures, especially shutting off power/gas and water completely. If you are uncomfortable working with basic plumbing, or especially electrical/gas connections, it's always safer to consult a qualified professional. Your safety is paramount.
Do I really need specialized pipe wrenches, or can I get by with regular adjustable wrenches for this job?
While it might be tempting to use adjustable wrenches, specialized pipe wrenches (like the 12-inch or 16-inch options listed) are highly recommended. They provide a much stronger, non-slip grip on rounded pipes and fittings, which is crucial for loosening a potentially corroded old T&P valve without damaging the water heater connections. This prevents frustration and potential leaks.
What's the most common mistake people make when replacing a T&P valve, and how can I avoid it?
The most common mistake is not properly sealing the new valve's threads, which leads to leaks after refilling the tank. To avoid this, always apply 3-5 layers of Teflon tape (clockwise) to the threads of the new T&P valve before screwing it into the tank. Also, ensure the discharge pipe is snug but not overtightened, especially if it's plastic, to prevent stripping.
How much time should I realistically set aside for this project, and what's the typical cost for parts?
While estimated at 3 hours, it's wise to set aside a half-day (4-5 hours) for this project to account for unexpected challenges like stubborn old valves or thorough draining/refilling. The primary cost is the new T&P valve itself, which usually ranges from $15-$30, plus a few dollars for Teflon tape and rags if you don't already have them.
Refill the Water Heater — Refill Tank and Check for Leaks
Part of project
How to Replace a Water Heater's T&P Relief Valve · Step 7 of 8
In this video
To refill the tank, first ensure the hot water faucet you opened earlier is still open. This allows air to escape as the tank fills. Then, fully open the cold water inlet shut-off valve. You will hear the tank begin to fill with water. While it's filling, check the new drain valve for any leaks or drips. Keep the hot water faucet open until a steady stream of water flows out, which indicates the tank is full of water and all the air has been purged. Once you have a steady stream, you can turn the faucet off.
Goal: Fill Tank with Water
- Check the new drain valve to make sure there are no leaks or drips as the tank fills.
Frequently Asked Questions
Is replacing a T&P relief valve a safe DIY project for a beginner, or should I call a professional?
This is a beginner-level plumbing task, but only if you strictly follow all safety procedures, especially shutting off power/gas and water completely. If you are uncomfortable working with basic plumbing, or especially electrical/gas connections, it's always safer to consult a qualified professional. Your safety is paramount.
Do I really need specialized pipe wrenches, or can I get by with regular adjustable wrenches for this job?
While it might be tempting to use adjustable wrenches, specialized pipe wrenches (like the 12-inch or 16-inch options listed) are highly recommended. They provide a much stronger, non-slip grip on rounded pipes and fittings, which is crucial for loosening a potentially corroded old T&P valve without damaging the water heater connections. This prevents frustration and potential leaks.
What's the most common mistake people make when replacing a T&P valve, and how can I avoid it?
The most common mistake is not properly sealing the new valve's threads, which leads to leaks after refilling the tank. To avoid this, always apply 3-5 layers of Teflon tape (clockwise) to the threads of the new T&P valve before screwing it into the tank. Also, ensure the discharge pipe is snug but not overtightened, especially if it's plastic, to prevent stripping.
How much time should I realistically set aside for this project, and what's the typical cost for parts?
While estimated at 3 hours, it's wise to set aside a half-day (4-5 hours) for this project to account for unexpected challenges like stubborn old valves or thorough draining/refilling. The primary cost is the new T&P valve itself, which usually ranges from $15-$30, plus a few dollars for Teflon tape and rags if you don't already have them.