Prepare and Cap the Copper Pipe — Install Tee Fitting and Arrestor
Part of project
How to Install a Water Hammer Arrestor to Stop Banging Pipes · Step 4 of 5
In this video
Prepare the remaining main copper line to be capped. Clean the male threads on the end of the pipe with a wire brush or emery cloth. Wrap the threads with Teflon tape in a clockwise direction. Screw on a brass compression cap and use channel-lock pliers or a wrench to tighten it securely, creating a watertight seal.
Goal: Seal copper pipe
- Wrap Teflon tape in the same direction you will be tightening the cap (clockwise) to prevent it from unraveling.
Used in this video
- Channel-Lock Pliers (Pliers_Type: Channel-Lock) — Gripping and tightening the brass compression cap onto the copper pipe.
- Wire Brush — Cleaning corrosion and debris from the pipe threads before applying sealant.
- Gloves — Protecting hands.
2.2M subscribers
FAQs
How do I accurately identify the source of water hammer before installing the arrestor?
Listen carefully for the banging sound when a specific faucet, toilet, or appliance (like a washing machine) shuts off abruptly. You can also try gently touching the water lines near suspect fixtures to feel for vibrations when the noise occurs. Installing the arrestor as close as possible to the identified source will yield the best results.
What crucial safety steps must I take before cutting into the water line?
Always turn off the main water supply to your entire home first. Then, open the lowest faucet in your house (e.g., in a basement or outdoor spigot) and the highest faucet to completely drain the water from the pipes. This prevents unexpected water leaks and potential injury while you work.
Do I need special tools to cut copper pipes, and how do I ensure a leak-free connection?
Yes, a copper pipe tubing cutter (e.g., AUTOCUT 1/2 in.) is essential for a clean, straight cut. After cutting, use a reamer and deburring tool (like the Husky 1-5/8 in.) to smooth the pipe's interior and exterior edges. This deburring step is critical for proper sealing and preventing leaks, especially with push-to-connect fittings.
What's the best way to prevent leaks when installing the tee fitting and water hammer arrestor?
Ensure the pipe ends are perfectly clean, smooth, and free of scratches or burrs. Use a depth gauge (like the Tectite Depth Gauge) to mark the correct insertion depth on the pipe for push-to-connect fittings, ensuring it's fully seated. For the arrestor's threaded connection, apply several wraps of PTFE plumber's tape (Harvey 1/2 in. x 260 in.) clockwise to the male threads before tightening.
Prepare and Cap the Copper Pipe — Install Tee Fitting and Arrestor
Part of project
How to Install a Water Hammer Arrestor to Stop Banging Pipes · Step 4 of 5
In this video
Prepare the remaining main copper line to be capped. Clean the male threads on the end of the pipe with a wire brush or emery cloth. Wrap the threads with Teflon tape in a clockwise direction. Screw on a brass compression cap and use channel-lock pliers or a wrench to tighten it securely, creating a watertight seal.
Goal: Seal copper pipe
- Wrap Teflon tape in the same direction you will be tightening the cap (clockwise) to prevent it from unraveling.
Used in this video
- Channel-Lock Pliers (Pliers_Type: Channel-Lock) — Gripping and tightening the brass compression cap onto the copper pipe.
- Wire Brush — Cleaning corrosion and debris from the pipe threads before applying sealant.
- Gloves — Protecting hands.
Frequently Asked Questions
How do I accurately identify the source of water hammer before installing the arrestor?
Listen carefully for the banging sound when a specific faucet, toilet, or appliance (like a washing machine) shuts off abruptly. You can also try gently touching the water lines near suspect fixtures to feel for vibrations when the noise occurs. Installing the arrestor as close as possible to the identified source will yield the best results.
What crucial safety steps must I take before cutting into the water line?
Always turn off the main water supply to your entire home first. Then, open the lowest faucet in your house (e.g., in a basement or outdoor spigot) and the highest faucet to completely drain the water from the pipes. This prevents unexpected water leaks and potential injury while you work.
Do I need special tools to cut copper pipes, and how do I ensure a leak-free connection?
Yes, a copper pipe tubing cutter (e.g., AUTOCUT 1/2 in.) is essential for a clean, straight cut. After cutting, use a reamer and deburring tool (like the Husky 1-5/8 in.) to smooth the pipe's interior and exterior edges. This deburring step is critical for proper sealing and preventing leaks, especially with push-to-connect fittings.
What's the best way to prevent leaks when installing the tee fitting and water hammer arrestor?
Ensure the pipe ends are perfectly clean, smooth, and free of scratches or burrs. Use a depth gauge (like the Tectite Depth Gauge) to mark the correct insertion depth on the pipe for push-to-connect fittings, ensuring it's fully seated. For the arrestor's threaded connection, apply several wraps of PTFE plumber's tape (Harvey 1/2 in. x 260 in.) clockwise to the male threads before tightening.