Install the Water Hammer Arrestors — Identify the Source and Gather Materials
Part of project
How to Install a Water Hammer Arrestor to Stop Banging Pipes · Step 1 of 5
In this video
Under the sink, use a wrench to disconnect the water supply line from the shutoff valve. Screw the prepared water hammer arrestor directly onto the shutoff valve. Then, connect the water supply line to the other end of the arrestor. Use the wrench to tighten all connections securely. Repeat this entire process for both the hot and cold water lines.
Goal: Connect the arrestors to the hot and cold water lines
Used in this video
- Wrench (Wrench Type: Open-end) — Tightening and loosening the compression nuts on the supply lines and arrestor.
2.2M subscribers
FAQs
How do I accurately identify the source of water hammer before installing the arrestor?
Listen carefully for the banging sound when a specific faucet, toilet, or appliance (like a washing machine) shuts off abruptly. You can also try gently touching the water lines near suspect fixtures to feel for vibrations when the noise occurs. Installing the arrestor as close as possible to the identified source will yield the best results.
What crucial safety steps must I take before cutting into the water line?
Always turn off the main water supply to your entire home first. Then, open the lowest faucet in your house (e.g., in a basement or outdoor spigot) and the highest faucet to completely drain the water from the pipes. This prevents unexpected water leaks and potential injury while you work.
Do I need special tools to cut copper pipes, and how do I ensure a leak-free connection?
Yes, a copper pipe tubing cutter (e.g., AUTOCUT 1/2 in.) is essential for a clean, straight cut. After cutting, use a reamer and deburring tool (like the Husky 1-5/8 in.) to smooth the pipe's interior and exterior edges. This deburring step is critical for proper sealing and preventing leaks, especially with push-to-connect fittings.
What's the best way to prevent leaks when installing the tee fitting and water hammer arrestor?
Ensure the pipe ends are perfectly clean, smooth, and free of scratches or burrs. Use a depth gauge (like the Tectite Depth Gauge) to mark the correct insertion depth on the pipe for push-to-connect fittings, ensuring it's fully seated. For the arrestor's threaded connection, apply several wraps of PTFE plumber's tape (Harvey 1/2 in. x 260 in.) clockwise to the male threads before tightening.
Install the Water Hammer Arrestors — Identify the Source and Gather Materials
Part of project
How to Install a Water Hammer Arrestor to Stop Banging Pipes · Step 1 of 5
In this video
Under the sink, use a wrench to disconnect the water supply line from the shutoff valve. Screw the prepared water hammer arrestor directly onto the shutoff valve. Then, connect the water supply line to the other end of the arrestor. Use the wrench to tighten all connections securely. Repeat this entire process for both the hot and cold water lines.
Goal: Connect the arrestors to the hot and cold water lines
Used in this video
- Wrench (Wrench Type: Open-end) — Tightening and loosening the compression nuts on the supply lines and arrestor.
Frequently Asked Questions
How do I accurately identify the source of water hammer before installing the arrestor?
Listen carefully for the banging sound when a specific faucet, toilet, or appliance (like a washing machine) shuts off abruptly. You can also try gently touching the water lines near suspect fixtures to feel for vibrations when the noise occurs. Installing the arrestor as close as possible to the identified source will yield the best results.
What crucial safety steps must I take before cutting into the water line?
Always turn off the main water supply to your entire home first. Then, open the lowest faucet in your house (e.g., in a basement or outdoor spigot) and the highest faucet to completely drain the water from the pipes. This prevents unexpected water leaks and potential injury while you work.
Do I need special tools to cut copper pipes, and how do I ensure a leak-free connection?
Yes, a copper pipe tubing cutter (e.g., AUTOCUT 1/2 in.) is essential for a clean, straight cut. After cutting, use a reamer and deburring tool (like the Husky 1-5/8 in.) to smooth the pipe's interior and exterior edges. This deburring step is critical for proper sealing and preventing leaks, especially with push-to-connect fittings.
What's the best way to prevent leaks when installing the tee fitting and water hammer arrestor?
Ensure the pipe ends are perfectly clean, smooth, and free of scratches or burrs. Use a depth gauge (like the Tectite Depth Gauge) to mark the correct insertion depth on the pipe for push-to-connect fittings, ensuring it's fully seated. For the arrestor's threaded connection, apply several wraps of PTFE plumber's tape (Harvey 1/2 in. x 260 in.) clockwise to the male threads before tightening.