Partially Drain the Tank — Drain the Water Heater
Part of project
How to Replace an Electric Water Heater Heating Element · Step 2 of 7
In this video
Connect a garden hose to the drain valve located at the bottom of the water heater tank. Place the other end of the hose in a floor drain or a large bucket. Open the drain valve to begin draining water from the tank. To speed up the draining process, lift the lever on the T&P relief valve; this allows air to enter the tank, breaking the vacuum. Continue draining until the water level is below the T&P valve port.
Goal: Lower water level below the T&P valve
- The water draining from the tank is extremely hot. Be careful to avoid burns.
Used in this video
- Garden Hose (brand: none, Tool Type: Plumbing Tools, Material: Rubber, Garden Hose Length: 25ft) — Draining water from the tank.
- Bucket (brand: none, Tool Type: Plumbing Tools, Material: Plastic, Bucket Size: 5 gallon) · optional — Collecting drained water if a floor drain is not available.
641K subscribers
FAQs
What are the most critical safety precautions I must take when replacing a water heater heating element?
The most critical step is ensuring the power to the water heater is completely OFF at your home's main electrical panel or breaker box before touching any wires. Also, turn off the cold water supply valve to the heater. Safely draining the tank of hot water is also essential to prevent burns.
Is a special tool required for removing the heating element, or can I use a standard wrench?
While some might attempt it with a large socket or pipe wrench, a specialized heating element wrench (like the 'Rheem PROTECH Dual Head Element Wrench' mentioned) is highly recommended. This tool is designed to fit the element's hex head perfectly, minimizing the risk of stripping it and making removal and tightening much easier.
How long should I expect this project to take, especially considering the draining process?
The estimated time for this project is 3 hours, but beginners should budget closer to 4 hours. Draining the water heater tank can take anywhere from 30 minutes to over an hour, depending on your tank's size and the drainage rate. Don't rush the process, especially during safety-critical steps.
What's a common mistake beginners make during installation, and how can I prevent leaks around the new element?
A common mistake is not properly seating the new heating element's gasket or not tightening the element sufficiently. To prevent leaks, ensure the new gasket is clean and properly aligned on the element before insertion. Tighten the element firmly with your specialized wrench, but avoid over-tightening which can damage the tank or element.
Partially Drain the Tank — Drain the Water Heater
Part of project
How to Replace an Electric Water Heater Heating Element · Step 2 of 7
In this video
Connect a garden hose to the drain valve located at the bottom of the water heater tank. Place the other end of the hose in a floor drain or a large bucket. Open the drain valve to begin draining water from the tank. To speed up the draining process, lift the lever on the T&P relief valve; this allows air to enter the tank, breaking the vacuum. Continue draining until the water level is below the T&P valve port.
Goal: Lower water level below the T&P valve
- The water draining from the tank is extremely hot. Be careful to avoid burns.
Used in this video
- Garden Hose (brand: none, Tool Type: Plumbing Tools, Material: Rubber, Garden Hose Length: 25ft) — Draining water from the tank.
- Bucket (brand: none, Tool Type: Plumbing Tools, Material: Plastic, Bucket Size: 5 gallon) · optional — Collecting drained water if a floor drain is not available.
Frequently Asked Questions
What are the most critical safety precautions I must take when replacing a water heater heating element?
The most critical step is ensuring the power to the water heater is completely OFF at your home's main electrical panel or breaker box before touching any wires. Also, turn off the cold water supply valve to the heater. Safely draining the tank of hot water is also essential to prevent burns.
Is a special tool required for removing the heating element, or can I use a standard wrench?
While some might attempt it with a large socket or pipe wrench, a specialized heating element wrench (like the 'Rheem PROTECH Dual Head Element Wrench' mentioned) is highly recommended. This tool is designed to fit the element's hex head perfectly, minimizing the risk of stripping it and making removal and tightening much easier.
How long should I expect this project to take, especially considering the draining process?
The estimated time for this project is 3 hours, but beginners should budget closer to 4 hours. Draining the water heater tank can take anywhere from 30 minutes to over an hour, depending on your tank's size and the drainage rate. Don't rush the process, especially during safety-critical steps.
What's a common mistake beginners make during installation, and how can I prevent leaks around the new element?
A common mistake is not properly seating the new heating element's gasket or not tightening the element sufficiently. To prevent leaks, ensure the new gasket is clean and properly aligned on the element before insertion. Tighten the element firmly with your specialized wrench, but avoid over-tightening which can damage the tank or element.