Take your new shower arm and the roll of thread seal tape. You will apply tape to the threads on both ends of the arm. For the end that goes into the wall, start at the second thread from the end and wrap the tape tightly in a clockwise direction. This is crucial—wrapping clockwise ensures the tape tightens as you screw the arm in, rather than unraveling. Overlap the tape by about half its width and make 3 to 5 full wraps. Repeat this process for the other end of the arm where the shower head will attach.
Step 1
⏱ 2 min
Gather Tools and Materials
Before beginning any work, gather all the necessary tools and your new components. Lay out the new shower head, new shower arm, and thread seal tape. Have your adjustable wrench or channel-lock pliers and a soft rag ready. Ensuring everything is within reach will make the process smoother and prevent interruptions.
Step 2
⏱ 2 min
Remove the Old Shower Head
Attempt to unscrew the old shower head from the existing shower arm by turning it counter-clockwise by hand. If it is too tight, wrap your soft rag around the connector nut of the shower head and use your adjustable wrench or channel-lock pliers to grip it. Turn counter-clockwise to loosen and remove it completely. Since you are replacing the arm, scratching it is not a major concern, but it is good practice to use the rag.
Step 3
⏱ 2 min
Remove the Old Shower Arm
The shower arm is screwed into a fitting inside the wall. Grip the arm firmly with your hands and turn it counter-clockwise to unscrew it. If it's too tight, you can insert the handle of your channel-lock pliers or a screwdriver into the opening of the arm to gain leverage. Apply steady, firm pressure. Be careful not to apply jerky or excessive force, as this can damage the fitting in the wall. Once loosened, continue unscrewing by hand until it is free. The decorative flange will slide off as you remove the arm.
Step 4
⏱ 2 min
Clean Threads and Flush Pipe
With the arm removed, look into the threaded female fitting in the wall. Use a rag or a small brush, like an old toothbrush, to clean out any old thread seal tape, plumber's putty, or mineral deposits. After cleaning, place a rag over the opening and turn the shower water on for just 2-3 seconds. This will flush out any loose debris that could clog your new shower head. Turn the water off immediately.
Step 5
⏱ 2 minApply Thread Seal Tape
Step 6
⏱ 2 min
Install the New Shower Arm
First, slide the new decorative flange (escutcheon) onto the long end of the new shower arm, ensuring its finished side faces away from the wall threads. Now, carefully insert the taped end of the arm into the fitting in the wall. Hand-tighten the arm by turning it clockwise until it is snug. Continue turning until it is pointing downwards at the correct angle. If you cannot get it tight enough by hand, use a rag-wrapped wrench on the straight part of the pipe for one final, gentle turn. Stop when it feels snug; do not overtighten. Slide the flange flush against the wall.
Step 7
⏱ 2 min
Install the New Shower Head
Ensure the small rubber washer is properly seated inside the threaded connector of the new shower head. Screw the new shower head onto the newly installed and taped shower arm. Turn it clockwise and hand-tighten it firmly. In most cases, hand-tightening is sufficient and recommended by manufacturers to avoid damaging the plastic threads or the washer. If the instructions specify using a tool, or if it leaks after hand-tightening, use your rag-wrapped wrench on the fitting's nut to give it a slight quarter-turn.
Step 8
⏱ 2 min
Check for Leaks
Turn the shower water on and carefully observe both connection points: where the shower arm enters the wall and where the shower head attaches to the arm. Look for any drips, sprays, or seeping water. Let the water run for a minute to ensure the seal holds under pressure. If you see a leak at the shower head, try tightening it slightly. If you see a leak at the wall, you will likely need to shut off the water, unscrew the arm, and re-apply the thread seal tape before reinstalling.
Step 5/8
Apply Thread Seal Tape2 min