Mark and Drill for Optional Lag Bolts — Mount the Sink Basin
Part of project
How to Install a Pedestal Sink · Step 4 of 8
In this video
Carefully place the sink onto the mounted brackets to test the fit. From underneath, use a pencil to mark the location of the optional mounting holes that go through the back of the sink. These are for additional support. Lift the sink off the brackets. Use a drill to create holes at the marked locations. Screw the provided lag bolts into these holes until they are snug against the wall.
Goal: Prepare for Secondary Support
- The sink is heavy. Use assistance when lifting it on and off the brackets to avoid injury or damage.
Used in this video
- Pencil — Marking hole locations.
- Drill — Drilling pilot holes for lag bolts.
- Adjustable Wrench — Tightening the lag bolts into the wall.
21K subscribers
FAQs
Do I really need all the specific tools listed, like the Hilti drill and Zircon stud finder?
For secure and accurate installation, a stud finder is highly recommended to ensure the basin is mounted to wall studs, preventing wobbling. While the Hilti drill is powerful, any corded hammer drill with appropriate masonry bits can work for drilling into tile or plaster if studs aren't accessible or for floor mounting, but ensure it's capable of making clean holes.
What's the most critical safety precaution to take before starting this pedestal sink installation?
The most critical step is to turn off the water supply to the entire house or at least the bathroom you're working in. This prevents accidental flooding when disconnecting old fixtures or if a new connection leaks during testing. Always double-check that the water is off before proceeding with any plumbing disconnections.
How long should a beginner expect this project to take, and what's a common time-consuming step?
For a beginner, plan for a full day (6-8 hours) for this project, especially if you're unfamiliar with plumbing. Removing the old sink, particularly if it's heavily caulked or secured, can often be the most time-consuming initial step. Take your time, as rushing often leads to mistakes.
What's the most common mistake beginners make that causes leaks after installation?
The most common mistake is not properly tightening or sealing the P-trap and water supply connections. Ensure all threaded connections are hand-tightened, then given an additional quarter to half-turn with pliers or a wrench, and always use plumber's tape or pipe dope on threaded water supply connections for a watertight seal.
Mark and Drill for Optional Lag Bolts — Mount the Sink Basin
Part of project
How to Install a Pedestal Sink · Step 4 of 8
In this video
Carefully place the sink onto the mounted brackets to test the fit. From underneath, use a pencil to mark the location of the optional mounting holes that go through the back of the sink. These are for additional support. Lift the sink off the brackets. Use a drill to create holes at the marked locations. Screw the provided lag bolts into these holes until they are snug against the wall.
Goal: Prepare for Secondary Support
- The sink is heavy. Use assistance when lifting it on and off the brackets to avoid injury or damage.
Used in this video
- Pencil — Marking hole locations.
- Drill — Drilling pilot holes for lag bolts.
- Adjustable Wrench — Tightening the lag bolts into the wall.
Frequently Asked Questions
Do I really need all the specific tools listed, like the Hilti drill and Zircon stud finder?
For secure and accurate installation, a stud finder is highly recommended to ensure the basin is mounted to wall studs, preventing wobbling. While the Hilti drill is powerful, any corded hammer drill with appropriate masonry bits can work for drilling into tile or plaster if studs aren't accessible or for floor mounting, but ensure it's capable of making clean holes.
What's the most critical safety precaution to take before starting this pedestal sink installation?
The most critical step is to turn off the water supply to the entire house or at least the bathroom you're working in. This prevents accidental flooding when disconnecting old fixtures or if a new connection leaks during testing. Always double-check that the water is off before proceeding with any plumbing disconnections.
How long should a beginner expect this project to take, and what's a common time-consuming step?
For a beginner, plan for a full day (6-8 hours) for this project, especially if you're unfamiliar with plumbing. Removing the old sink, particularly if it's heavily caulked or secured, can often be the most time-consuming initial step. Take your time, as rushing often leads to mistakes.
What's the most common mistake beginners make that causes leaks after installation?
The most common mistake is not properly tightening or sealing the P-trap and water supply connections. Ensure all threaded connections are hand-tightened, then given an additional quarter to half-turn with pliers or a wrench, and always use plumber's tape or pipe dope on threaded water supply connections for a watertight seal.