Install New Cartridge — Clean Faucet Body
Part of project
How to Stop a Dripping Single-Handle Kitchen Faucet by Replacing the Cartridge · Step 8 of 11
In this video
Before inserting the new cartridge, check inside the valve body and remove any old rubber washers or seals left behind. Align the new cartridge correctly—it is typically keyed with a notch (a 'V' shape in this case) to fit only one way. Push the new cartridge firmly into the valve body until it is fully seated.
Goal: Properly seat the new cartridge into the valve body
- The new cartridge can only be installed in one orientation. Look for alignment markings on the cartridge and valve body.
3.6M subscribers
FAQs
What tools will I definitely need for this specific faucet cartridge replacement?
You'll primarily need a screwdriver (like the Milwaukee Flat Head), an adjustable wrench (such as the Crescent AC212VS), and pliers (like the Husky Groove Joint or Channellock Long Nose) to disassemble and reassemble the faucet components. A hex key set (GEARWRENCH 83510) might also be necessary if your handle uses set screws.
How can I ensure I purchase the correct replacement cartridge for my single-handle kitchen faucet?
The most crucial step is identifying your faucet's brand and model number, usually found under the sink or on the faucet itself. If that's not possible, carefully remove the old cartridge and take it to a hardware store to match it, like the MOEN 1225 specified in the materials, to ensure compatibility.
What are the most common mistakes beginners make during this project, and how can I avoid them?
A common mistake is not fully shutting off the water supply, so always confirm both hot and cold valves are off. Another is losing small parts like screws or the retaining clip (OMUR Connecting Clips) down the drain, which can be prevented by plugging the sink drain with a rag or towel (WYPALL L40 Towels).
How long should this project take for a beginner, and is it truly a 'beginner' difficulty task?
Yes, this is a beginner-friendly project, designed to be straightforward for most DIYers. For someone new to plumbing, it should typically take about 30-60 minutes, assuming you have the correct replacement cartridge and all necessary tools readily available.
Install New Cartridge — Clean Faucet Body
Part of project
How to Stop a Dripping Single-Handle Kitchen Faucet by Replacing the Cartridge · Step 8 of 11
In this video
Before inserting the new cartridge, check inside the valve body and remove any old rubber washers or seals left behind. Align the new cartridge correctly—it is typically keyed with a notch (a 'V' shape in this case) to fit only one way. Push the new cartridge firmly into the valve body until it is fully seated.
Goal: Properly seat the new cartridge into the valve body
- The new cartridge can only be installed in one orientation. Look for alignment markings on the cartridge and valve body.
Frequently Asked Questions
What tools will I definitely need for this specific faucet cartridge replacement?
You'll primarily need a screwdriver (like the Milwaukee Flat Head), an adjustable wrench (such as the Crescent AC212VS), and pliers (like the Husky Groove Joint or Channellock Long Nose) to disassemble and reassemble the faucet components. A hex key set (GEARWRENCH 83510) might also be necessary if your handle uses set screws.
How can I ensure I purchase the correct replacement cartridge for my single-handle kitchen faucet?
The most crucial step is identifying your faucet's brand and model number, usually found under the sink or on the faucet itself. If that's not possible, carefully remove the old cartridge and take it to a hardware store to match it, like the MOEN 1225 specified in the materials, to ensure compatibility.
What are the most common mistakes beginners make during this project, and how can I avoid them?
A common mistake is not fully shutting off the water supply, so always confirm both hot and cold valves are off. Another is losing small parts like screws or the retaining clip (OMUR Connecting Clips) down the drain, which can be prevented by plugging the sink drain with a rag or towel (WYPALL L40 Towels).
How long should this project take for a beginner, and is it truly a 'beginner' difficulty task?
Yes, this is a beginner-friendly project, designed to be straightforward for most DIYers. For someone new to plumbing, it should typically take about 30-60 minutes, assuming you have the correct replacement cartridge and all necessary tools readily available.