Method 1: Trim the Sink Tailpiece — Connect P-Trap to Wall Drain
Part of project
How to Plumb a Double Kitchen Sink Drain with a Garbage Disposal · Step 6 of 8
In this video
The first and most straightforward solution is to shorten the sink's tailpiece (the pipe extending down from the pop-up drain assembly). By measuring and cutting off the excess length from the bottom of the tailpiece, you can raise the entire P-trap assembly, allowing the trap arm to align correctly with the higher wall drain.
Goal: Raise the P-trap to align with the wall drain
Used in this video
- Hacksaw — Cutting the plastic or metal tailpiece.
- Tape Measure — Measuring the required length to cut from the tailpiece.
2K subscribers
FAQs
How difficult is it to plumb a double kitchen sink with a garbage disposal for a beginner, and how long should I expect it to take?
This project is rated as beginner-friendly, but requires patience and attention to detail. For a DIY novice, plan to set aside 3-5 hours, especially if you encounter unexpected issues or need to make precise cuts. The material cost, including the disposal and plumbing parts, typically ranges from $150-$400 depending on the quality and features chosen.
Are all the listed tools, especially specialized cutters and reamers, truly essential for this plumbing project?
While basic tools like Channellock pliers and a screwdriver are essential, specialized tools like the RIDGID PTEC 3000 plastic tubing cutter and the Husky Reamer are highly recommended. They ensure clean, burr-free cuts on plastic pipes, which significantly reduces the risk of leaks and makes assembly much easier. You could use a hacksaw for cuts, but meticulous deburring would then be critical.
What are the most common mistakes that lead to leaks after installing a double sink drain and garbage disposal, and how can I prevent them?
The most common causes of leaks are improperly tightened slip-nut connections, not using plumber's putty correctly around the sink flange, and misaligned P-trap components. Always hand-tighten slip nuts first, then use your Channellock pliers for an additional half-turn, ensuring all washers are seated perfectly. Thoroughly test for leaks by running water and inspecting every connection with paper towels.
What specific safety precautions should I take when working under the sink, especially with a garbage disposal and water lines?
Safety is paramount. Always disconnect power to the garbage disposal at the circuit breaker before beginning any work on it. Turn off the water supply to the sink at the shut-off valves or main house valve. Wear safety glasses to protect your eyes from debris, and use gloves to avoid contact with old grime or chemicals.
TranscriptHide
Auto-generated transcript. May contain errors.
Method 1: Trim the Sink Tailpiece — Connect P-Trap to Wall Drain
Part of project
How to Plumb a Double Kitchen Sink Drain with a Garbage Disposal · Step 6 of 8
In this video
The first and most straightforward solution is to shorten the sink's tailpiece (the pipe extending down from the pop-up drain assembly). By measuring and cutting off the excess length from the bottom of the tailpiece, you can raise the entire P-trap assembly, allowing the trap arm to align correctly with the higher wall drain.
Goal: Raise the P-trap to align with the wall drain
Used in this video
- Hacksaw — Cutting the plastic or metal tailpiece.
- Tape Measure — Measuring the required length to cut from the tailpiece.
Frequently Asked Questions
How difficult is it to plumb a double kitchen sink with a garbage disposal for a beginner, and how long should I expect it to take?
This project is rated as beginner-friendly, but requires patience and attention to detail. For a DIY novice, plan to set aside 3-5 hours, especially if you encounter unexpected issues or need to make precise cuts. The material cost, including the disposal and plumbing parts, typically ranges from $150-$400 depending on the quality and features chosen.
Are all the listed tools, especially specialized cutters and reamers, truly essential for this plumbing project?
While basic tools like Channellock pliers and a screwdriver are essential, specialized tools like the RIDGID PTEC 3000 plastic tubing cutter and the Husky Reamer are highly recommended. They ensure clean, burr-free cuts on plastic pipes, which significantly reduces the risk of leaks and makes assembly much easier. You could use a hacksaw for cuts, but meticulous deburring would then be critical.
What are the most common mistakes that lead to leaks after installing a double sink drain and garbage disposal, and how can I prevent them?
The most common causes of leaks are improperly tightened slip-nut connections, not using plumber's putty correctly around the sink flange, and misaligned P-trap components. Always hand-tighten slip nuts first, then use your Channellock pliers for an additional half-turn, ensuring all washers are seated perfectly. Thoroughly test for leaks by running water and inspecting every connection with paper towels.
What specific safety precautions should I take when working under the sink, especially with a garbage disposal and water lines?
Safety is paramount. Always disconnect power to the garbage disposal at the circuit breaker before beginning any work on it. Turn off the water supply to the sink at the shut-off valves or main house valve. Wear safety glasses to protect your eyes from debris, and use gloves to avoid contact with old grime or chemicals.
Video Transcript
(226 characters)Hide
Video Transcript
(226 characters)Transcript may be auto-generated and contain errors.