Disassemble the Faucet and Remove Valve Stem — Remove the Packing Nut and Valve Stem
Part of project
How to Stop a Dripping Two-Handle Faucet · Step 3 of 7
In this video
To fix a leak from the handle, first shut off the water. Then, remove the screw in the center of the handle and pull the handle off. Use an adjustable wrench to loosen and remove the packing nut. With the nut removed, you can now pull the entire long valve stem straight out of the faucet body.
Goal: Remove valve stem
Used in this video
- Screwdriver (Tool Type: Screwdrivers) — Removing the screw that holds the faucet handle in place.
- Adjustable Wrench (Tool Type: Wrenches) — Unscrewing the packing nut to release the valve stem.
1.1M subscribers
FAQs
Do I need the specific brand-name tools listed, or can I use generic alternatives for this faucet repair?
No, specific brands are not strictly necessary. A basic set of screwdrivers (Phillips and flathead), an adjustable wrench, and a pair of pliers are usually sufficient for this project. The listed tools are recommendations for quality and ease of use, but common household tools will often suffice.
What is the absolute most important safety precaution I should take before starting this repair?
The most critical step is to completely shut off the water supply to the faucet before any disassembly. This usually involves turning the shut-off valves under the sink clockwise until tight, then confirming the water is off by turning on the faucet.
As a beginner, how much time should I set aside for this project, and what's the typical cost involved?
For a beginner, expect to spend about 30 to 60 minutes on this repair. The cost is typically very low, usually under $10-$20 for replacement washers, O-rings, and plumber's grease, as the main components are inexpensive.
I replaced the washer and O-ring, but my faucet is still dripping. What could be the problem?
If the drip persists, carefully inspect the valve seat for corrosion, nicks, or debris after removing the stem again. A damaged valve seat often needs to be cleaned or replaced, or the new washer/O-ring might not be seated properly or is the wrong size.
Disassemble the Faucet and Remove Valve Stem — Remove the Packing Nut and Valve Stem
Part of project
How to Stop a Dripping Two-Handle Faucet · Step 3 of 7
In this video
To fix a leak from the handle, first shut off the water. Then, remove the screw in the center of the handle and pull the handle off. Use an adjustable wrench to loosen and remove the packing nut. With the nut removed, you can now pull the entire long valve stem straight out of the faucet body.
Goal: Remove valve stem
Used in this video
- Screwdriver (Tool Type: Screwdrivers) — Removing the screw that holds the faucet handle in place.
- Adjustable Wrench (Tool Type: Wrenches) — Unscrewing the packing nut to release the valve stem.
Frequently Asked Questions
Do I need the specific brand-name tools listed, or can I use generic alternatives for this faucet repair?
No, specific brands are not strictly necessary. A basic set of screwdrivers (Phillips and flathead), an adjustable wrench, and a pair of pliers are usually sufficient for this project. The listed tools are recommendations for quality and ease of use, but common household tools will often suffice.
What is the absolute most important safety precaution I should take before starting this repair?
The most critical step is to completely shut off the water supply to the faucet before any disassembly. This usually involves turning the shut-off valves under the sink clockwise until tight, then confirming the water is off by turning on the faucet.
As a beginner, how much time should I set aside for this project, and what's the typical cost involved?
For a beginner, expect to spend about 30 to 60 minutes on this repair. The cost is typically very low, usually under $10-$20 for replacement washers, O-rings, and plumber's grease, as the main components are inexpensive.
I replaced the washer and O-ring, but my faucet is still dripping. What could be the problem?
If the drip persists, carefully inspect the valve seat for corrosion, nicks, or debris after removing the stem again. A damaged valve seat often needs to be cleaned or replaced, or the new washer/O-ring might not be seated properly or is the wrong size.