Remove the Discharge Pipe
Part of project
How to Replace a Water Heater's T&P Relief Valve · Step 4 of 10
This guide provides comprehensive, step-by-step instructions for safely replacing a leaking or faulty Temperature and Pressure (T&P) relief valve on a residential water heater. The process involves shutting off the power and water supply, partially draining the tank, removing the old valve and its discharge pipe, installing a new, correctly-rated valve with fresh thread sealant, and then carefully restoring the system to full operation. This procedure assumes you are working on an electric water heater with the T&P valve located on the side of the tank, and you are replacing a valve that is currently leaking.
201K subscribers
FAQs
What are the most critical safety steps I must take before replacing the T&P valve?
Always shut off both the electrical power to the water heater at the breaker panel and the cold water supply valve leading into the heater. Failure to do so can lead to severe electrocution, scalding injuries from hot water, or significant water damage. Partially draining the tank reduces pressure and hot water volume, making the job safer.
Can I use regular pliers or an adjustable wrench instead of a heavy-duty pipe wrench to remove the old T&P valve?
A heavy-duty pipe wrench, like the TradesPro 14 in. recommended, is strongly advised. Old T&P valves are often corroded and incredibly tight, requiring significant torque to loosen. Using regular pliers or an adjustable wrench might strip the valve's hex head or slip, making removal much harder and potentially damaging the water heater's tank fitting.
How long should this project take for a beginner, and what's the typical cost involved?
For a DIY beginner, expect this project to take approximately 1 to 2 hours from start to finish, including preparation and cleanup. The primary cost will be for the new T&P relief valve itself, which typically ranges from $15-$30. If you need to purchase specific tools, that will be an additional one-time cost.
My new T&P valve is still leaking slightly after installation. What could be the problem?
A common cause for a persistent leak is insufficient or improperly applied thread sealant. Ensure you wrap 4-5 layers of PTFE plumber's tape clockwise around the threads of the new valve, starting one thread back from the end. Also, confirm the valve is tightened adequately, but avoid overtightening, which can crack the tank's port.
Remove the Discharge Pipe
Part of project
How to Replace a Water Heater's T&P Relief Valve · Step 4 of 10
This guide provides comprehensive, step-by-step instructions for safely replacing a leaking or faulty Temperature and Pressure (T&P) relief valve on a residential water heater. The process involves shutting off the power and water supply, partially draining the tank, removing the old valve and its discharge pipe, installing a new, correctly-rated valve with fresh thread sealant, and then carefully restoring the system to full operation. This procedure assumes you are working on an electric water heater with the T&P valve located on the side of the tank, and you are replacing a valve that is currently leaking.
Frequently Asked Questions
What are the most critical safety steps I must take before replacing the T&P valve?
Always shut off both the electrical power to the water heater at the breaker panel and the cold water supply valve leading into the heater. Failure to do so can lead to severe electrocution, scalding injuries from hot water, or significant water damage. Partially draining the tank reduces pressure and hot water volume, making the job safer.
Can I use regular pliers or an adjustable wrench instead of a heavy-duty pipe wrench to remove the old T&P valve?
A heavy-duty pipe wrench, like the TradesPro 14 in. recommended, is strongly advised. Old T&P valves are often corroded and incredibly tight, requiring significant torque to loosen. Using regular pliers or an adjustable wrench might strip the valve's hex head or slip, making removal much harder and potentially damaging the water heater's tank fitting.
How long should this project take for a beginner, and what's the typical cost involved?
For a DIY beginner, expect this project to take approximately 1 to 2 hours from start to finish, including preparation and cleanup. The primary cost will be for the new T&P relief valve itself, which typically ranges from $15-$30. If you need to purchase specific tools, that will be an additional one-time cost.
My new T&P valve is still leaking slightly after installation. What could be the problem?
A common cause for a persistent leak is insufficient or improperly applied thread sealant. Ensure you wrap 4-5 layers of PTFE plumber's tape clockwise around the threads of the new valve, starting one thread back from the end. Also, confirm the valve is tightened adequately, but avoid overtightening, which can crack the tank's port.