Cut the Pipe — Cut the Copper Pipe
Part of project
How to Install a Water Hammer Arrestor to Stop Banging Pipes · Step 3 of 7
In this video
Place the pipe cutter around the pipe where the cut is desired. Tighten the cutter's handle until the cutting wheel makes contact, then give it an additional one-eighth turn. Rotate the entire cutter one full revolution around the pipe. Tighten the handle another eighth of a turn and rotate again. Repeat this incremental tightening and rotating process until the cutter slices completely through the pipe.
Goal: Cut the pipe to length.
- Do not over-tighten the cutter handle at the start or between rotations, as this can damage or break the cutting wheel.
Used in this video
- Pipe Cutter (brand: Ridgid, Tool Type: Hand tools) — Slicing through the metal pipe.
32K subscribers
FAQs
Do I really need all the listed tools for this water hammer arrestor installation, or can I manage with fewer?
For a successful and leak-free installation, the tubing cutter, deburring tool, and adjustable wrenches are essential. While you might try a hacksaw, a tubing cutter ensures a cleaner, square cut vital for compression fittings. The deburring tool prevents damage to the O-ring and ensures a tight seal, so these are not optional for a reliable outcome.
What are the critical safety precautions I must take when installing a water hammer arrestor, especially as a beginner working with plumbing?
Always begin by shutting off the main water supply to your home and draining the lines to prevent unexpected floods or sprays. Wear safety glasses to protect against debris and gloves to prevent cuts from sharp pipe edges. Double-check that the water is completely off before making any cuts to the pipe.
How much time should a beginner budget for this water hammer arrestor installation, and what's the approximate material cost?
A beginner should typically budget 1 to 2 hours for this project, allowing time for preparation, precise cutting, assembly, and thorough leak checks. The primary material cost will be for the water hammer arrestor itself and the compression tee, generally ranging from $30-$60 depending on your specific chosen parts and local pricing.
What are the most common mistakes beginners make when installing a water hammer arrestor, and how can I avoid them?
A frequent mistake is not deburring the pipe ends thoroughly, which can lead to leaks at the compression fitting due to an improper seal. Another common error is under-tightening the compression nuts; ensure they are snug and firm, but avoid overtightening and stripping the threads. Also, remember to use Teflon tape on the arrestor's threaded connection points, but not on the compression connections themselves.
Cut the Pipe — Cut the Copper Pipe
Part of project
How to Install a Water Hammer Arrestor to Stop Banging Pipes · Step 3 of 7
In this video
Place the pipe cutter around the pipe where the cut is desired. Tighten the cutter's handle until the cutting wheel makes contact, then give it an additional one-eighth turn. Rotate the entire cutter one full revolution around the pipe. Tighten the handle another eighth of a turn and rotate again. Repeat this incremental tightening and rotating process until the cutter slices completely through the pipe.
Goal: Cut the pipe to length.
- Do not over-tighten the cutter handle at the start or between rotations, as this can damage or break the cutting wheel.
Used in this video
- Pipe Cutter (brand: Ridgid, Tool Type: Hand tools) — Slicing through the metal pipe.
Frequently Asked Questions
Do I really need all the listed tools for this water hammer arrestor installation, or can I manage with fewer?
For a successful and leak-free installation, the tubing cutter, deburring tool, and adjustable wrenches are essential. While you might try a hacksaw, a tubing cutter ensures a cleaner, square cut vital for compression fittings. The deburring tool prevents damage to the O-ring and ensures a tight seal, so these are not optional for a reliable outcome.
What are the critical safety precautions I must take when installing a water hammer arrestor, especially as a beginner working with plumbing?
Always begin by shutting off the main water supply to your home and draining the lines to prevent unexpected floods or sprays. Wear safety glasses to protect against debris and gloves to prevent cuts from sharp pipe edges. Double-check that the water is completely off before making any cuts to the pipe.
How much time should a beginner budget for this water hammer arrestor installation, and what's the approximate material cost?
A beginner should typically budget 1 to 2 hours for this project, allowing time for preparation, precise cutting, assembly, and thorough leak checks. The primary material cost will be for the water hammer arrestor itself and the compression tee, generally ranging from $30-$60 depending on your specific chosen parts and local pricing.
What are the most common mistakes beginners make when installing a water hammer arrestor, and how can I avoid them?
A frequent mistake is not deburring the pipe ends thoroughly, which can lead to leaks at the compression fitting due to an improper seal. Another common error is under-tightening the compression nuts; ensure they are snug and firm, but avoid overtightening and stripping the threads. Also, remember to use Teflon tape on the arrestor's threaded connection points, but not on the compression connections themselves.