Turn Off Water — Locate and Mark the Area
Part of project
How to Install a Plumbing Access Panel for Future Repairs · Step 1 of 7
In this video
Turn off the water supply to the shower. This is typically done by locating the shut-off valves for the shower, which may be located near the shower itself or in a central plumbing access panel. The valves should be turned clockwise to close and stop the flow of water. The presenter points out the hot and cold supply lines and the shower control valve in a cutaway wall.
Goal: Prevent water from flowing
- Double-check that the water is completely off by briefly turning on the shower controls.
3.6M subscribers
FAQs
How can I ensure I don't cut into pipes, wires, or studs behind the drywall?
Always use a reliable stud finder (like the DEWALT DW0150) to scan the area for studs, electrical wiring, and plumbing lines before marking your cut. After marking, make a series of small, shallow pilot holes with a drill or jab saw to visually confirm the cavity is clear before making your main cuts. If you hit an obstruction, stop immediately and reassess.
Where is the ideal location to install a plumbing access panel?
Install the panel directly over the specific plumbing components you need to access, such as shut-off valves, cleanouts, or fixture P-traps. Choose an area that provides sufficient working room behind the wall once the panel is open. Ideally, select a spot between two studs to avoid cutting structural elements, confirmed with your stud finder.
What if I accidentally cut the drywall opening too large for my access panel?
If the opening is slightly oversized, you can often compensate by applying a thicker bead of construction adhesive (like Loctite Power Grab Express) and caulk around the panel's flange to fill the gap. For larger errors, you might need to patch the drywall with a repair kit and recut, or purchase a slightly larger access panel to cover the mistake. Measure twice, cut once to avoid this common issue.
Can I use a regular utility knife for cutting the drywall, or is a jab saw necessary?
While a utility knife (like the FASTCAP Triblade) can be used for some straight cuts, a jab saw (such as the Milwaukee Folding Jab Saw) is highly recommended for this project. It provides better leverage and control for cutting through drywall, especially for internal corners and thicker sections, resulting in cleaner and more precise openings.
Turn Off Water — Locate and Mark the Area
Part of project
How to Install a Plumbing Access Panel for Future Repairs · Step 1 of 7
In this video
Turn off the water supply to the shower. This is typically done by locating the shut-off valves for the shower, which may be located near the shower itself or in a central plumbing access panel. The valves should be turned clockwise to close and stop the flow of water. The presenter points out the hot and cold supply lines and the shower control valve in a cutaway wall.
Goal: Prevent water from flowing
- Double-check that the water is completely off by briefly turning on the shower controls.
Frequently Asked Questions
How can I ensure I don't cut into pipes, wires, or studs behind the drywall?
Always use a reliable stud finder (like the DEWALT DW0150) to scan the area for studs, electrical wiring, and plumbing lines before marking your cut. After marking, make a series of small, shallow pilot holes with a drill or jab saw to visually confirm the cavity is clear before making your main cuts. If you hit an obstruction, stop immediately and reassess.
Where is the ideal location to install a plumbing access panel?
Install the panel directly over the specific plumbing components you need to access, such as shut-off valves, cleanouts, or fixture P-traps. Choose an area that provides sufficient working room behind the wall once the panel is open. Ideally, select a spot between two studs to avoid cutting structural elements, confirmed with your stud finder.
What if I accidentally cut the drywall opening too large for my access panel?
If the opening is slightly oversized, you can often compensate by applying a thicker bead of construction adhesive (like Loctite Power Grab Express) and caulk around the panel's flange to fill the gap. For larger errors, you might need to patch the drywall with a repair kit and recut, or purchase a slightly larger access panel to cover the mistake. Measure twice, cut once to avoid this common issue.
Can I use a regular utility knife for cutting the drywall, or is a jab saw necessary?
While a utility knife (like the FASTCAP Triblade) can be used for some straight cuts, a jab saw (such as the Milwaukee Folding Jab Saw) is highly recommended for this project. It provides better leverage and control for cutting through drywall, especially for internal corners and thicker sections, resulting in cleaner and more precise openings.