Connect New Supply Line — Connect Water Supply Line
Part of project
How to Install a New Dishwasher · Step 6 of 9
In this video
Attach the new braided stainless steel supply line to the outlet port on the new angle stop valve. Hand-tighten the connector nut, then use pliers to give it a final snug quarter-turn. Finally, wipe down the entire valve and connection with a clean paper towel to ensure it's dry, which will make it easier to spot any leaks after turning the water back on.
Goal: Connect new water supply line
- Be careful not to cross-thread the supply line nut. It should screw on smoothly by hand before you use a tool.
Used in this video
- Pliers (Pliers Type: Slip-joint pliers) — Giving the supply line connection a final tightening.
- Paper Towel — Wiping the valve and connections dry.
719K subscribers
FAQs
What are the most critical safety steps to take before starting to disconnect the old dishwasher?
Always turn off the water supply valve leading to the dishwasher and cut power at the circuit breaker first. This prevents potential leaks, electrical shocks, and damage while working with water lines and electrical connections.
What are the most common causes of leaks when connecting the hot water supply line and drain hose, and how can I prevent them?
Leaks often stem from improperly tightened connections or insufficient Teflon tape on threaded fittings. Ensure fittings are hand-tightened, then turn an additional 1/2 to 1 full turn with a wrench, and apply Teflon tape only to male threaded connections to create a watertight seal.
The project is listed as 'beginner' with an estimated 5 hours; is this realistic for someone with no plumbing experience, and what factors might extend the timeline?
While beginner-friendly, 5 hours is an estimate for straightforward installations. If you encounter seized fittings, rusted pipes, or need to adjust cabinetry, it could take longer. Having all tools and materials ready beforehand will help keep you on track.
Besides the listed tools, what other items should a beginner have on hand in case of unexpected issues during removal or installation?
A small shop-vac for unexpected spills is invaluable. Additionally, having a utility knife to cut the drain hose to length and possibly a basin wrench if the old water supply connection is in a very tight spot could save you a trip to the hardware store.
Connect New Supply Line — Connect Water Supply Line
Part of project
How to Install a New Dishwasher · Step 6 of 9
In this video
Attach the new braided stainless steel supply line to the outlet port on the new angle stop valve. Hand-tighten the connector nut, then use pliers to give it a final snug quarter-turn. Finally, wipe down the entire valve and connection with a clean paper towel to ensure it's dry, which will make it easier to spot any leaks after turning the water back on.
Goal: Connect new water supply line
- Be careful not to cross-thread the supply line nut. It should screw on smoothly by hand before you use a tool.
Used in this video
- Pliers (Pliers Type: Slip-joint pliers) — Giving the supply line connection a final tightening.
- Paper Towel — Wiping the valve and connections dry.
Frequently Asked Questions
What are the most critical safety steps to take before starting to disconnect the old dishwasher?
Always turn off the water supply valve leading to the dishwasher and cut power at the circuit breaker first. This prevents potential leaks, electrical shocks, and damage while working with water lines and electrical connections.
What are the most common causes of leaks when connecting the hot water supply line and drain hose, and how can I prevent them?
Leaks often stem from improperly tightened connections or insufficient Teflon tape on threaded fittings. Ensure fittings are hand-tightened, then turn an additional 1/2 to 1 full turn with a wrench, and apply Teflon tape only to male threaded connections to create a watertight seal.
The project is listed as 'beginner' with an estimated 5 hours; is this realistic for someone with no plumbing experience, and what factors might extend the timeline?
While beginner-friendly, 5 hours is an estimate for straightforward installations. If you encounter seized fittings, rusted pipes, or need to adjust cabinetry, it could take longer. Having all tools and materials ready beforehand will help keep you on track.
Besides the listed tools, what other items should a beginner have on hand in case of unexpected issues during removal or installation?
A small shop-vac for unexpected spills is invaluable. Additionally, having a utility knife to cut the drain hose to length and possibly a basin wrench if the old water supply connection is in a very tight spot could save you a trip to the hardware store.