Reinstall and Test the Disposal — Final Test
Part of project
How to Install an In-Sink Air Switch for a Garbage Disposal · Step 6 of 6
In this video
Mount the reassembled disposal back under the sink. Lift it up and engage the tabs with the sink flange. Turn the mounting ring clockwise to lock it securely in place. Reconnect the main drain elbow and tighten its fittings. Reattach the dishwasher hose and secure its clamp. Once all plumbing is reconnected, plug the unit back into the electrical outlet. Restore power at the circuit breaker. Run water and briefly turn on the disposal to test for proper operation and check for any leaks.
Goal: Return the disposal to service and check for leaks
- Before turning on the switch, run cold water into the sink to check for leaks at your plumbing connections.
Used in this video
- Disposal Wrench / Screwdriver (brand: Unspecified, Tool Type: Screwdriver, Power Source: Manual, Material: Metal, Size: Large, Specific Use: Fastening) — Tightening the mounting ring.
236K subscribers
FAQs
Do I really need a specific 1-5/16 inch hole saw for the air switch button, or can I use a different size drill bit?
Using the recommended 1-5/16 inch hole saw is crucial for a clean, precise cut and a snug fit for the air switch button. An incorrect size could lead to a loose fit, potential water ingress, or difficulty in securing the button properly. While other methods might exist, the hole saw provides the best result for durability and safety.
What are the most important safety precautions I need to take before starting this installation, especially since it involves electrical components near water?
Always turn off the power to your garbage disposal circuit at the breaker before beginning any work, and confirm it's off with a non-contact voltage tester. Ensure your work area under the sink is completely dry, and after installation, thoroughly check for any leaks around the new switch and existing plumbing connections before restoring power.
My air switch button is installed, but the garbage disposal isn't turning on when I press it. What should I check first?
First, verify that the power control module is plugged into a functioning outlet and the garbage disposal is securely plugged into the module. Next, check that the air tube is firmly connected to both the air switch button under the sink and the power control module. A kinked or disconnected air tube is a common issue.
Is there an alternative to drilling a hole in my sink deck if I'm hesitant to do so?
Yes, if you have an existing unused pre-drilled hole in your sink deck (like for a soap dispenser or old sprayer), you can often use that. Alternatively, some air switch kits offer options for mounting directly into the countertop instead of the sink, or you can purchase a separate countertop-mounted button that doesn't require drilling into the sink.
TranscriptHide
Auto-generated transcript. May contain errors.
Reinstall and Test the Disposal — Final Test
Part of project
How to Install an In-Sink Air Switch for a Garbage Disposal · Step 6 of 6
In this video
Mount the reassembled disposal back under the sink. Lift it up and engage the tabs with the sink flange. Turn the mounting ring clockwise to lock it securely in place. Reconnect the main drain elbow and tighten its fittings. Reattach the dishwasher hose and secure its clamp. Once all plumbing is reconnected, plug the unit back into the electrical outlet. Restore power at the circuit breaker. Run water and briefly turn on the disposal to test for proper operation and check for any leaks.
Goal: Return the disposal to service and check for leaks
- Before turning on the switch, run cold water into the sink to check for leaks at your plumbing connections.
Used in this video
- Disposal Wrench / Screwdriver (brand: Unspecified, Tool Type: Screwdriver, Power Source: Manual, Material: Metal, Size: Large, Specific Use: Fastening) — Tightening the mounting ring.
Frequently Asked Questions
Do I really need a specific 1-5/16 inch hole saw for the air switch button, or can I use a different size drill bit?
Using the recommended 1-5/16 inch hole saw is crucial for a clean, precise cut and a snug fit for the air switch button. An incorrect size could lead to a loose fit, potential water ingress, or difficulty in securing the button properly. While other methods might exist, the hole saw provides the best result for durability and safety.
What are the most important safety precautions I need to take before starting this installation, especially since it involves electrical components near water?
Always turn off the power to your garbage disposal circuit at the breaker before beginning any work, and confirm it's off with a non-contact voltage tester. Ensure your work area under the sink is completely dry, and after installation, thoroughly check for any leaks around the new switch and existing plumbing connections before restoring power.
My air switch button is installed, but the garbage disposal isn't turning on when I press it. What should I check first?
First, verify that the power control module is plugged into a functioning outlet and the garbage disposal is securely plugged into the module. Next, check that the air tube is firmly connected to both the air switch button under the sink and the power control module. A kinked or disconnected air tube is a common issue.
Is there an alternative to drilling a hole in my sink deck if I'm hesitant to do so?
Yes, if you have an existing unused pre-drilled hole in your sink deck (like for a soap dispenser or old sprayer), you can often use that. Alternatively, some air switch kits offer options for mounting directly into the countertop instead of the sink, or you can purchase a separate countertop-mounted button that doesn't require drilling into the sink.
Video Transcript
(272 characters)Hide
Video Transcript
(272 characters)Transcript may be auto-generated and contain errors.