Spraying Interior Walls With An Airless Paint Sprayer. How to paint drywall. DIY painting.

So, here we go. Now, we're going to be stepping on to uh part three for this video, and that's actually spraying the top coat. And the and there's not a whole lot of difference when it comes to spraying the top coat versus the the primer, the PVA primer, except that I'll be spraying a lot slower and getting it on really, really heavy. I want to really saturate those walls and get them soaking wet with paint. Uh not to the point that it's going to run, but pretty close to that point. So, I'm going to be using a 1221 tip again with my 30-in extension. This house, the ceilings are going to be pure white. So, we'll be spraying those after we do the walls. So, I'm going to be doing my walls first and then I'll be spraying my ceilings. The trim is actually a stain package. Everything's going to be stained and lacquered. And the builder on this job wants it all stained and lacquered down and then installed. So, uh, we're just painting the walls in this job and they're doing the stain and lacquer package themselves. But if I was actually doing the stain and lacquer package myself, I'd install all the trim stain and lacquer grit. Then I'd do my walls and ceilings. And but um, when I'm doing that here, we're just doing the walls and ceilings, and we're doing two colors. So, I'm going to be spraying my walls, and then I'll be masking my walls, dropping it with plastic, and then spraying my ceilings. But we'll give the walls a day to dry and then we'll come back and spray the ceilings. So once again, I got my sprayer set up out there. I just quickly cleaned it out and now we got our top coat loaded into it and I'll begin spraying it. It's set up at 2200 PSI and I'll play around with the pressure, but it's going to be somewhere between 2200 and 3,000 PSI. Be using a 1221 tip, a 30 in gun extension. Don't forget all those tools and accessories can be purchased on my tool store. You can just click on my tool store link right there. That'll take you right to my tool store where you can purchase any of my tools and accessories. And so here we go. I don't got to spray the ceiling. So I'll be just doing the walls and we'll be saturating those walls. Here we go. And once again, this process is a lot like doing the PVA primer, but just a lot slower. We're getting our sprayer set up here now. getting our uh product uh set up in here. We're using a product from SH Wind called Treasure Valley Hake Shell. And this is a really good new construction paint. Sprays very well, hangs very well. You can get it on really thick without it running. So, prior to spraying these walls, we're I'm spraying right now. We're working through here spraying, but we're also cocking the windows and just running a bead of cocking right around where the tape meets uh is actually taped onto the window. That way, no paint will bleed onto the vinyl, the window. And prior to it actually drying, the cocking and the paint drying, we're pulling that masking off. And so, just cruising right along here, spraying, and I'll show you uh that spraying process here. And then some of the pulling down of the masking Just continuing the cruise right along here. Spraying here and spraying with my 30-in extension and my 1221 tip. If you have any questions about tip sizes and what tip sizes to use, I do got a video right here and that will teach you about what tip sizes to use and when to use them. So, you can go check out that video anytime uh after you're done watching this video. [Music] A few simple little tips here while you're spraying. I'm actually keeping the tip of my gun about 12 in away from the wall. And while I'm actually spraying this um paint, I'm actually looking at it actually going onto the wall. And I want to see it go there and just saturate that wall. If it looks a little bit dry, you want to slow down. If it looks like it's getting too heavy, just speed it up. But you really got to pay attention to the paint as it's going on that wall. Now, while this paint is still wet around these windows, we want to pull this masking off. Otherwise, the paint will bridge from the plastic over to the window and it'll peel off the paint. So, you just got to be really careful and pull it off while it's wet. [Applause] Well, you can have a good look at after about about 3 hours worth of work what I look like completely covered in paint paint dust. This is about the worst uh part of painting that there is. And this is new construction painting. Extremely dirty, extremely dusty. and I actually don't like doing it, but I'm doing this video just to teach you how to paint a brand new home with bare drywall. And okay, now the this whole interior is all sprayed. The body is sprayed. Now we're just cleaning up and we're going to let this dry for today and we'll come back and actually spray the ceilings and we'll just be you can see just take my monkey suit off here and they'll be all clean and then be coming back tomorrow and showing you how to mask the ceilings. So, another quick uh tip when you're actually spraying your walls, uh get a shop back out to vacuum all your floors. And if you vacuum your floors inside your hallways or your closets, you won't get any kickback that's flying up and to and stick it onto your wet walls. Cuz when you're in the closet and you're spraying, you get down to the floor, it has a tendency to throw a lot of dirt and debris around if your floors aren't clean. So, just get a shop back. Uh vacuum all your floors up, get them all nice and clean prior to spraying them. Also, here's another uh simple tip. When you're actually spraying, I'm using a 30-in extension. And the reason why I use that extension is so I can reach the ceilings and reach the floors without having to get on a ladder, without having to bend over. But along uh with that extension comes the gun spinning and you'll see me spraying. And that's why I'm typically in a a bedroom, I'm only releasing the trigger just a couple times. I'm trying never to release that trigger, going up and down, spraying. And it's going to be a lot faster to spray without releasing the trigger, but you're not going to get spits in areas that you don't uh want to get on. Cuz with a 30-in extension, you're going to get a pretty large spit. You don't want to get spits in the middle of the wall. So, when you're working around windows and stuff, you're trying to spray it without releasing your trigger so you don't get any spits. Well, I'm just about done spraying the body here. And once we're done spraying the body, we're just going to clean stuff up. And then we're going to let this dry. And then we're going to come back to spray the ceiling. And that's going to be the fourth part of this ceiling. Spraying that second color in the living room is actually a third color. It's going to be a green color. So, we're going to do that at the same time. So, you want to stay uh and watch the next video. Click on the video right here. And we're going to show you the process of how we mask the walls off. They actually sprayed the ceilings now with a pure